 |
|
Titania nanotubes create potentially efficient solar cells
February 08, 2006A solar cell, made of titania nanotubes and natural dye, may be the answer to making solar electricity production cost-effective, according to a Penn State researcher.
"Solar cell technology has not changed very much over time and is still predominantly silicon solar cells," says Dr. Craig Grimes, professor of electrical engineering and materials science and engineering. "It takes a great deal of energy, 5 gigajoules per square meter, to make silicon solar cells. It can be argued that silicon solar cells never fully recover the energy it takes to make them in the first place."
The new focus in solar cells is toward dye sensitive solar cells, which have been made using nanoparticles and a variety of dyes.
"Nanoparticle solar cells are the gold standard of this new approach," says Grimes. "However, because of limitations, it appears they have gotten as good as they are going to get."
The researchers are instead looking at titania nanotubes to replace the particulate coatings in dye sensitive solar cells and, their initial attempt produced about 3 percent conversion of solar energy to electricity, they report in today's issue of Nano Letters. The researcher's inability to grow longer titania nanotubes, constrained the solar conversion rate.
"I think we can reach a 15 percent conversion rate with these cells, and other researchers do as well," says Grimes. "That is 15 percent with a relatively easy fabrication system that is commercially viable."
Conventional solar cells are made from blocks of slowly made silicon boules that are sliced into wafers. Grimes and his team use an easier approach. They coat a piece of glass with a fluorine-doped tin oxide and then sputter on a layer of titanium. The researchers can currently lay down a 500-nanometer thick titanium layer. They then anodize the layer by placing it in an acidic bath with a mild electric current and titanium dioxide nanotube arrays grow to about 360 nanometers. The tubes are then heated in oxygen so that they crystalize. The process turns the opaque coating of titanium into a transparent coating of nanotubes.
This nanotube array is then coated in a commercially available dye. The dye-coated nanotubes make up the negative electrode and a positive electrode seals the cell which contains an iodized electrolyte. When sun shines through the glass, the energy falls on the dye molecules and an electron is freed. If this electron and others make their way out of the tube to the negative electrode, a current flows. Many electrons do not and are recombined, but the tube structure of the titanium dioxide allows an order of magnitude more electrons to make it to the electrode than with particulate coatings.
"There is still a great deal of optimization of the design that needs to be done," says Grimes. "Now, with the help of the Pennsylvania Energy Development Authority, we will have equipment to make high quality titanium coatings that are thicker. If we get about 3 percent conversion with 360 nanometers, what we could get with 4 microns is an exciting question we soon hope to answer."
The thickness of the titanium layer constrains the height of the nanotubes. With thicker initial coatings, longer tubes would produce more electrons that do not recombine, producing more electricity.
Other aspects of the titania nanotube dye sensitive solar cells that need to be optimized include the thickness of the cells. Currently, spacers separate the two layers and provide internal support. These spacers are 25 microns thick. If the spacers could be made as sturdy, but shorter, there would be less of a distance for the electrons to travel and more electrons will make it across the electrodes.
Penn State
"Nanoparticle solar cells are the gold standard of this new approach," says Grimes. "However, because of limitations, it appears they have gotten as good as they are going to get."
The researchers are instead looking at titania nanotubes to replace the particulate coatings in dye sensitive solar cells and, their initial attempt produced about 3 percent conversion of solar energy to electricity, they report in today's issue of Nano Letters. The researcher's inability to grow longer titania nanotubes, constrained the solar conversion rate.
"I think we can reach a 15 percent conversion rate with these cells, and other researchers do as well," says Grimes. "That is 15 percent with a relatively easy fabrication system that is commercially viable."
Conventional solar cells are made from blocks of slowly made silicon boules that are sliced into wafers. Grimes and his team use an easier approach. They coat a piece of glass with a fluorine-doped tin oxide and then sputter on a layer of titanium. The researchers can currently lay down a 500-nanometer thick titanium layer. They then anodize the layer by placing it in an acidic bath with a mild electric current and titanium dioxide nanotube arrays grow to about 360 nanometers. The tubes are then heated in oxygen so that they crystalize. The process turns the opaque coating of titanium into a transparent coating of nanotubes.
This nanotube array is then coated in a commercially available dye. The dye-coated nanotubes make up the negative electrode and a positive electrode seals the cell which contains an iodized electrolyte. When sun shines through the glass, the energy falls on the dye molecules and an electron is freed. If this electron and others make their way out of the tube to the negative electrode, a current flows. Many electrons do not and are recombined, but the tube structure of the titanium dioxide allows an order of magnitude more electrons to make it to the electrode than with particulate coatings.
"There is still a great deal of optimization of the design that needs to be done," says Grimes. "Now, with the help of the Pennsylvania Energy Development Authority, we will have equipment to make high quality titanium coatings that are thicker. If we get about 3 percent conversion with 360 nanometers, what we could get with 4 microns is an exciting question we soon hope to answer."
The thickness of the titanium layer constrains the height of the nanotubes. With thicker initial coatings, longer tubes would produce more electrons that do not recombine, producing more electricity.
Other aspects of the titania nanotube dye sensitive solar cells that need to be optimized include the thickness of the cells. Currently, spacers separate the two layers and provide internal support. These spacers are 25 microns thick. If the spacers could be made as sturdy, but shorter, there would be less of a distance for the electrons to travel and more electrons will make it across the electrodes.
Penn State
Solar Cells Current Events and Solar Cells News RSSUnderstanding mechanical properties of silicon nanowires paves way for nanodevices
Silicon nanowires are attracting significant attention from the electronics industry due to the drive for ever-smaller electronic devices, from cell phones to computers.
Vibrations key to efficiency of green fluorescent protein
University of California, Berkeley, chemists have discovered the secret to the success of a jellyfish protein whose green glow has made it the darling of biologists and the subject of the 2008 Nobel Prize in Physiology or Medicine.
Chemists describe solar energy progress and challenges, including the 'artificial leaf'
Scientists are making progress toward development of an "artificial leaf" that mimics a real leaf's chemical magic with photosynthesis - but instead converts sunlight and water into a liquid fuel such as methanol for cars and trucks.
Toward better solar cells: Chemists gain control of light-harvesting paths
University of Florida chemists have pioneered a method to tease out promising molecular structures for capturing energy, a step that could speed the development of more efficient, cheaper solar cells.
Switzerland has sent its first satellite into space
The Indian launcher Polar Space Launch Vehicle took off at 8:22 a.m. - Swiss time. Twenty minutes later, the SwissCube was ejected from the nose cone of the rocket at an altitude of around 720 kilometers.
Engineers Produce 'How-To' Guide for Controlling the Structure of Nanoparticles
Tiny objects known as nanoparticles are often heralded as holding great potential for future applications in electronics, medicine and other areas.
Looking deeply into polymer solar cells
Researchers from the Eindhoven University of Technology and the University of Ulm have made the first high-resolution 3D images of the inside of a polymer solar cell.
Carbon nanotubes could make efficient solar cells
Using a carbon nanotube instead of traditional silicon, Cornell researchers have created the basic elements of a solar cell that hopefully will lead to much more efficient ways of converting light to electricity than now used in calculators and on rooftops.
Gold Solution for Enhancing Nanocrystal Electrical Conductance
In a development that holds much promise for the future of solar cells made from nanocrystals, and the use of solar energy to produce clean and renewable liquid transportation fuels, researchers with the U.S. Department of Energy's Lawrence Berkeley National Laboratory (Berkeley Lab) have reported a technique by which the electrical conductivity of nanorod crystals of the semiconductor cadmium-selenide was increased 100,000 times.
Light at the speed of a bicycle and much more
The speed of light, 300 million metres per second, was long thought an immutable constant and has defined our understanding of matter and energy but recent research in the area of optics and photonics is proving that we can manipulate light to some ingenious and hugely lucrative ends.
More Solar Cells Current Events and Solar Cells News Articles
 |
solar cell |
 |
Crystalline Silicon Solar Cells: Technology and Systems Applications by Adolf Goetzberger (Author), Joachim Knobloch (Author), Bernhard Voss (Author) As environmental concerns escalate, solar power is increasingly seen as an attractive alternative energy source. Crystalline Silicon Solar Cells addresses the practical and theoretical issues fundamental to the viable conversion of sunlight into electricity. Written by three internationally renowned experts, this valuable reference profits from results and experience gained from research at the Fraunhofer Institute for Solar Energy Systems. Features include: Introduction to the principles of photovoltaics, providing a grounding in semiconductor physics for the novice reader Special emphasis on the methods of attaining high efficiency and thereby cost-effective solar power Examination of the physics, design and technology of crystalline silicon solar cells, in particular thin film cells... |
 |
SOLAR CELL, 60MM X 60MM X2MM by Solar Output: approximately 3 Volts @ 40 mA. 60mm square x 2.5mm thick epoxy-encapsulated silicon photovoltaic cell. Solid, almost-unbreakable module with solderable foil strips on backside. Ideal for solar-powered battery chargers and other projects. |
 |
Xantrex Technologies 852-2071 Xpower AC/DC Powerpack Solar With 400 Watt Inverter, Two AC Outlets, USB Port, And Digital Display by Xantrex Technologies The XPower Powerpack Solar is the first portable power pack that incorporates solar power in a compact, portable power source. It's completely self-renewing, which means the detachable 5-watt solar panel has the ability to recharge the power pack's 10 amp-hour battery.The 5-watt solar panel captures stores and converts the sun's renewable energy, replenishes the XPower Powerpack Solar's battery, and extends the runtime of many devices by up to 25 percent. |
 |
The Physics of Solar Cells (Properties of Semiconductor Materials) by Jenny Nelson (Author) This book provides a comprehensive introduction to the physics of the photovoltaic cell. It is suitable for undergraduates, graduate students, and researchers new to the field. It covers: basic physics of semiconductors in photovoltaic devices; physical models of solar cell operation; characteristics and design of common types of solar cell; and approaches to increasing solar cell efficiency. The text explains the terms and concepts of solar cell device physics and shows the reader how to formulate and solve relevant physical problems. Exercises and worked solutions are included. Contents: Photons In, Electrons Out: Basic Principles of PV; Electrons and Holes in Semiconductors; Generation and Recombination; Junctions; Analysis of the p n Junction; Monocrystalline Solar Cells; Thin... |
 |
Lenmar PPUS20 PowerPort Solar Charger & External Portable Lithium Ion Battery for Cell Phone/iPhone 3G/MP3/USB Charging Cable/Device Tip Adapters by Lenmar Battery Solutions The PowerPort Solar Charger and Battery has been designed to harness the sun's energy, shortening the process of transforming it into electricity by using photovoltaic cells (PVs). PVs convert sunlight into electricity that can be used immediately. The process is clean, fast, noiseless, and - thanks to Lenmar - easily portable. Here's how it works. Light from the sun hits the solar cells. exciting electrons within the cell. Some of them break free, and channeled through a conductive metal strip to create an electric current. This current can either be stored in a battery or used directly in the form of electricity. The stronger the sunlight and the more rays that hit the cell, the more electricity is generated. Lenmar's PowerPort Solar is a portable Lithium-ion battery that can be... |
 |
Solar Cells: Materials, Manufacture and Operation by Tom Markvart (Author), Luis Castaner (Author) The capture and use of solar energy has been growing for many years, but only in recent times have advances in design and manufacture allowed us to see the incorporation of solar energy as a significant player in the renewable energy arena. Solar cells are at the heart of any photovoltaic system and in this book the various types are described and their characteristics reviewed. Going beyond materials, design and function, 'Solar Cells' also covers their testing, monitoring and calibration thus providing a comprehensive account of current activity in this important field of research and industry. 'Solar Cells' has been abstracted from the recent 'Practical Handbook of Photovoltaics' by the same editors (ISBN 185617 3909. 2003: Elsevier) ... |
 |
Etón FR160B Microlink Self-Powered AM/FM/NOAA Weather Radio with Flashlight, Solar Power and Cell Phone Charger (Black) by Grundig / Eton Self-Powered AM/FM/NOAA Weather Radio with Flashlight, Solar Power, and Cell Phone Charger |
 |
Etón American Red Cross ARCFR160R Microlink Self-Powered AM/FM/NOAA Weather Radio with Flashlight, Solar Power and Cell Phone Charger (Red) by Grundig / Eton Self-Powered AM/FM/NOAA Weather Radio with Flashlight, Solar Power, and Cell Phone Charger |
 |
Physics of Solar Cells: From Basic Principles to Advanced Concepts (Physics Textbook) by Peter Würfel (Author) Based on the highly regarded and extremely successful first edition, this thoroughly revised, updated and expanded edition contains the latest knowledge on the mechanisms of solar energy conversion. The textbook describes in detail all aspects of solar cell function, the physics behind every single step, as well as all the issues to be considered when improving solar cells and their efficiency. Requiring no more than standard physics knowledge, the book enables both students and researchers to understand the factors driving conversion efficiency and to apply this knowledge to their own solar cell development. New exercises after each chapter help students to consolidate their freshly acquired knowledge, while the book also serves as a reference for researchers... |
| © 2009 BrightSurf.com |