 |
|
TU Delft tests windmill for seawater desalination
March 03, 2008A traditional windmill which drives a pump: that is the simple concept behind the combination of windmill/reverse osmosis developed by the Delft University of Technology (TU Delft) in The Netherlands. In this case, it involves a high-pressure pump which pushes water through a membrane using approximately 60 bar. This reverse osmosis membrane produces fresh water from seawater directly. The windmill is suited for use by, for instance, small villages in isolated, dry coastal areas.
The combination of windmills and desalination installations is already commercially available. These windmills produce electricity from wind power, the electricity is stored and subsequently used to drive the high-pressure pump for the reverse osmosis installation. The storage of electricity in particular is very expensive. Energy is also lost during conversion.
In the TU Delft installation, the high-pressure pump is driven directly by wind power. Water storage can be used to overcome calm periods. The storage of water is after all a great deal cheaper than that of electricity.
Robust
The chosen windmill is normally used for irrigation purposes. These windmills turn relatively slowly and are also very robust. On the basis of the windmill's capacity at varying wind speeds, it is estimated that it will produce 5 to 10 m3 of fresh water per day: enough drinking water for a small village of 500 inhabitants. A water reservoir will have to ensure that enough water is available for a calm period lasting up to five days. Three safeguards (in the event of the installation running dry, a low number of revolutions or a high number of revolutions) are also performed mechanically so that no electricity is needed.
Prototype
The first prototype has been built and is already working at a location near the A13 motorway near Delft. This prototype is to be dismantled and transported to Curaçao the first week of March. There the concept will be tested on seawater.
More information
The research is being sponsored by Mr Grootscholten, Aqua-for-All, Hatenboer and SenterNovem. Please see http://www.drinkingwiththewind.nl for more information.
Delft University of Technology
The chosen windmill is normally used for irrigation purposes. These windmills turn relatively slowly and are also very robust. On the basis of the windmill's capacity at varying wind speeds, it is estimated that it will produce 5 to 10 m3 of fresh water per day: enough drinking water for a small village of 500 inhabitants. A water reservoir will have to ensure that enough water is available for a calm period lasting up to five days. Three safeguards (in the event of the installation running dry, a low number of revolutions or a high number of revolutions) are also performed mechanically so that no electricity is needed.
Prototype
The first prototype has been built and is already working at a location near the A13 motorway near Delft. This prototype is to be dismantled and transported to Curaçao the first week of March. There the concept will be tested on seawater.
More information
The research is being sponsored by Mr Grootscholten, Aqua-for-All, Hatenboer and SenterNovem. Please see http://www.drinkingwiththewind.nl for more information.
Delft University of Technology
Windmill Current Events and Windmill News RSSOn the crest of wave energy
The ocean is a potentially vast source of electric power, yet as engineers test new technologies for capturing it, the devices are plagued by battering storms, limited efficiency, and the need to be tethered to the seafloor.
Keeping our sights on big breakers with radar
Scientists of the Geesthacht GKSS Research Centre have developed a radar system with which it is possible to study the behaviour of sea waves.
Analysis of windmill pitching shows risk of injury to biceps in softball players
Contrary to common belief, softball pitching subjects the biceps to high forces and torques when the player's arm swings around to release the ball, according to an analysis of muscle firing patterns conducted at Rush University Medical Center.
Nano machine of the future captures great scientist's bold vision
An idea conceived by one of the world's greatest scientists nearly 150 years ago has finally been realised with a tiny machine that could eventually lead to lasers moving objects remotely.
No more hammering please!
Whether it's inspecting glider wings or modern windmill rotor blades, today's method is archaic. Using tap testing, the experienced ear listens for hollow spaces and other defects. A much faster process measures heat distribution resolved over distance and time. Rotor blades for wind turbines are manufactured in the same way as in the good old days of the homemade surfboard. Layer by layer, fiberglass mats are laminated by hand with epoxy resin or other adhesives. The hulls, as long as 60 meters, are then joined together to form a rotor blade. The interior of the curved shell, tall enough to walk through, is reinforced with spars to ensure that the entire structure is capable of braving the
Light from wind and waves
Engineers of PROEKTSTROYSERVIS (Kaliningrad) know how to make the stormy sea work. They have designed a unique sea-based wind-and-wave plant, which allows to convert the energy of wind and waves into electricity. The plant is not afraid of any storms. In appearance, the entire construction is reminiscent of a float, UFO or the restaurant in the Ostankino TV Tower: a broad circle put on a counterbalance stick. The circle ensures floatation, it resembles a hollow washer made of metal, its diameter making at least 30 meters (this is half the length of the sea-wave in the Baltic Sea) and the displacement being equal to 250 tons. A through shaft is in the center. The counterbalance is inside the
More Windmill Current Events and Windmill News Articles
 |
Smv Industries 48A 8' American Windmill by SMV INDUSTRIES 8' American Windmill, Lawn Ornament, Easily Assembled, Steel Contruction With Galvanized Metal Rigging, Roller Bearings In Wheel. |
 |
The Boy Who Harnessed the Wind: Creating Currents of Electricity and Hope by William Kamkwamba (Author), Bryan Mealer (Author) William Kamkwamba was born in Malawi, a country where magic ruled and modern science was mystery. It was also a land withered by drought and hunger, and a place where hope and opportunity were hard to find. But William had read about windmills in a book called Using Energy, and he dreamed of building one that would bring electricity and water to his village and change his life and the lives of those around him. His neighbors may have mocked him and called him misala--crazy--but William was determined to show them what a little grit and ingenuity could do. Enchanted by the workings of electricity as a boy, William had a goal to study science in Malawi's top boarding schools. But in 2002, his country was stricken with a famine that left his family's farm devastated and his parents... |
 |
Green Science Windmill Generator by Toysmith by Toy Smith How is energy produced by using windmills? Build this amazing wind generator and learn about renewable energy/ "green energy". Watch the LED glow as it is powered by free energy from the wind. No batteries required! Help save the planet by using a recycled plastic bottle to support your wind generator. Ages 8+ |
 |
Ornamental Windmill is an Eye-Catching Replica of the Real Thing by Northern Tool and Equipment Indicates wind direction! Add rural charm to your grounds. Authentic, built-to-scale windmill replica has smooth and silent ball bearing operation. Heavy gauge steel construction. Durable outdoor finish is aluminum color with red trim. Includes anchor stakes. 8 feet in height. 22in. Wheel Dimension. U.S.A. |
 |
Licensed John Deere® Steel Windmill by JOHN DEERE John Deere Windmill is a decorative and functional work of art! PRICED RIGHT! Who knows which way the wind blows? You will, when you bring home this new John Deere Windmill! Windmill stands 8 feet high, all the better to catch the breeze! Heavy-duty all-steel construction means this big guy is built to last. 22" diameter blades turn on a lubricated ball-bearing fitting, making this Windmill as functional as it is decorative. Show your pride for years to come with this officially licensed piece of Americana! Wind worker: Traditional green and yellow paint is powder-coated for maximum weather resistance; Proudly features John Deere logo; Blade assembly rotates on grease-packed bearing for years of maintenance-free use; All-steel construction.; Windmill stands 8' high, has footprint of 27 x... |
|
Learning Curve Brands Thomas Wooden Railway - Toby's Windmill by Rc2 Little engineers can recreate their favorite scenes from the story "Toby's Windmill" in the "Thomas and the Really Brave Engines" video, or they can dream up their own countless adventures on Sodor with Toby's Windmill. Simply push down on the lever to rotate the windmill's blades, and send your trains chugging through the windmill. Load flour onto the train with the windmill's barrel loader. Includes wooden windmill, barrel cars and two flour barrels. | |
 |
Sunforce 44444 12-Volt 400-Watt Wind Generator by Sunforce The Sunforce 44444 400 Watt Wind Generator uses wind to generate power and run your appliances and electronics. Constructed from lightweight, weatherproof cast aluminum, this generator is also a great choice for powering pumps or charging batteries for large power demands. With a maximum power up to 400 watts or 27 amps, this device features a fully integrated regulator that automatically shuts down when the batteries are completely charged. The 44444 is virtually maintenance free with only two moving parts, and the carbon fiber composite blades ensure low wind noise while the patented high wind over speed technology guarantees a smooth, clean charge. Assembly is required, but this generator installs easily and mounts to any sturdy pole, building, or the Sunforce 44455 Wind Generator... |
 |
8ft Patriotic Decorative Windmill Red, White & Blue NEW by ToolsNow If your love of country doesn't depend on which way the wind blows, youll appreciate this decorative windmill. It stands 8 feet tall and features weather-resistant coated steel in red, white and blue. The 22 1/2in. dia. wheel adds a nice touch to your landscaping. Ball bearings for quiet operation; includes three 12in. ground stakes. |
 |
The Wind at Work: An Activity Guide to Windmills by Gretchen Woelfle (Author) Gretchen Woelfle traces the history of windmills and how their design and function have changed over times and includes more than a dozen wind-related activities such as making a wind sock and wind vane, cooking a traditional windmiller meal, sewing windmill patterns, and keeping track of a household's energy use. 75 b&w photos, 14 illus., 15 charts & graphs. |
 |
4.5' American Windmill by SMV INDUSTRIES 4.5' American Windmill, Lawn Ornament, Easily Assembled, Steel Construction With Galvanized Metal Rigging, Roller Bearings In Wheel. |
| © 2009 BrightSurf.com |