 |
|
Popcorn-ball design doubles efficiency of dye-sensitized solar cells
April 11, 2008A new approach is able to create a dramatic improvement in cheap solar cells now being developed in laboratories.
By using a popcorn-ball design -- tiny kernels clumped into much larger porous spheres -- researchers at the University of Washington are able to manipulate light and more than double the efficiency of converting solar energy to electricity. The findings will be presented today in New Orleans at the national meeting of the American Chemical Society.
"We think this can lead to a significant breakthrough in dye-sensitized solar cells," said lead author Guozhong Cao, a UW professor of materials science and engineering.
Dye-sensitized solar cells, first popularized in a scientific article in 1991, are more flexible, easier to manufacture and cheaper than existing solar technologies. Researchers have tried various rough surfaces and achieved higher and higher efficiencies. Current lab prototypes can convert just over one tenth of the incoming sun's energy into electricity. This is about half as efficient as the commercial, silicon-based cells used in rooftop panels and calculators.
The UW researchers did not attempt to maximize the overall efficiency of a dye-sensitized solar cell to match or beat these previous records. Instead, they focused on developing new approaches and compared the performance of a homogeneous rough surface with a clumping design. One of the main quandaries in making an efficient solar cell is the size of the grains. Smaller grains have bigger surface area per volume, and thus absorb more rays. But bigger clumps, closer to the wavelength of visible light, cause light to ricochet within the thin light-absorbing surface so it has a higher chance of being absorbed.
"You want to have a larger surface area by making the grains smaller," Cao said. "But if you let the light bounce back and forth several times, then you have more chances of capturing the energy."
Other researchers have tried mixing larger grains in with the small particles to scatter the light, but have little success in boosting efficiency. The UW group instead made only very tiny grains, about 15 nanometers across. (Lining up 3,500 grains end to end would equal the width of a human hair.) Then they clumped these into larger agglomerations, about 300 nanometers across. The larger balls scatter incoming rays and force light to travel a longer distance within the solar cell. The balls' complex internal structure, meanwhile, creates a surface area of about 1,000 square feet for each gram of material. This internal surface is coated with a dye that captures the light.
The researchers expected some improvement in the performance but what they saw exceeded their hopes.
"We did not expect the doubling," Cao said. "It was a happy surprise."
The overall efficiency was 2.4 percent using only small particles, which is the highest efficiency achieved for this material. With the popcorn-ball design, results presented today at the conference show an efficiency of 6.2 percent, more than double the previous performance.
"The most significant finding is the amount of increase using this unique approach," Cao said.
The experiments were performed using zinc oxide, which is less stable chemically than the more commonly used titanium oxide but easier to work with.
"We first wanted to prove the concept in an easier material. Now we are working on transferring this concept to titanium oxide," Cao said. Titanium oxide based dye-sensitized solar cells are now at 11 percent maximum efficiency. Cao hopes his strategy could push dye-sensitized solar cells' efficiency significantly over that threshold.
The research was funded by the National Science Foundation, the Department of Energy, Washington Technology Center and the Air Force Office of Scientific Research. Co-authors are postdoctoral researcher Qifeng Zhang, research associate Tammy Chou and graduate student Bryan Russo, all in the UW's department of materials science and engineering and Samson Jenekhe, a UW professor of chemical engineering.
University of Washington
Dye-sensitized solar cells, first popularized in a scientific article in 1991, are more flexible, easier to manufacture and cheaper than existing solar technologies. Researchers have tried various rough surfaces and achieved higher and higher efficiencies. Current lab prototypes can convert just over one tenth of the incoming sun's energy into electricity. This is about half as efficient as the commercial, silicon-based cells used in rooftop panels and calculators.
The UW researchers did not attempt to maximize the overall efficiency of a dye-sensitized solar cell to match or beat these previous records. Instead, they focused on developing new approaches and compared the performance of a homogeneous rough surface with a clumping design. One of the main quandaries in making an efficient solar cell is the size of the grains. Smaller grains have bigger surface area per volume, and thus absorb more rays. But bigger clumps, closer to the wavelength of visible light, cause light to ricochet within the thin light-absorbing surface so it has a higher chance of being absorbed.
"You want to have a larger surface area by making the grains smaller," Cao said. "But if you let the light bounce back and forth several times, then you have more chances of capturing the energy."
Other researchers have tried mixing larger grains in with the small particles to scatter the light, but have little success in boosting efficiency. The UW group instead made only very tiny grains, about 15 nanometers across. (Lining up 3,500 grains end to end would equal the width of a human hair.) Then they clumped these into larger agglomerations, about 300 nanometers across. The larger balls scatter incoming rays and force light to travel a longer distance within the solar cell. The balls' complex internal structure, meanwhile, creates a surface area of about 1,000 square feet for each gram of material. This internal surface is coated with a dye that captures the light.
The researchers expected some improvement in the performance but what they saw exceeded their hopes.
"We did not expect the doubling," Cao said. "It was a happy surprise."
The overall efficiency was 2.4 percent using only small particles, which is the highest efficiency achieved for this material. With the popcorn-ball design, results presented today at the conference show an efficiency of 6.2 percent, more than double the previous performance.
"The most significant finding is the amount of increase using this unique approach," Cao said.
The experiments were performed using zinc oxide, which is less stable chemically than the more commonly used titanium oxide but easier to work with.
"We first wanted to prove the concept in an easier material. Now we are working on transferring this concept to titanium oxide," Cao said. Titanium oxide based dye-sensitized solar cells are now at 11 percent maximum efficiency. Cao hopes his strategy could push dye-sensitized solar cells' efficiency significantly over that threshold.
The research was funded by the National Science Foundation, the Department of Energy, Washington Technology Center and the Air Force Office of Scientific Research. Co-authors are postdoctoral researcher Qifeng Zhang, research associate Tammy Chou and graduate student Bryan Russo, all in the UW's department of materials science and engineering and Samson Jenekhe, a UW professor of chemical engineering.
University of Washington
Dye-sensitized Solar Cells Current Events and Dye-sensitized Solar Cells News RSSAncient diatoms lead to new technology for solar energy
Engineers at Oregon State University have discovered a way to use an ancient life form to create one of the newest technologies for solar energy, in systems that may be surprisingly simple to build compared to existing silicon-based solar cells.
New efficiency benchmark for dye-sensitized solar cells
In a paper published online June 29 in the journal Nature Materials, EPFL professor Michael Graetzel, Shaik Zakeeruddin and colleagues from the Changchun Institute of Applied Chemistry at the Chinese Academy of Sciences have achieved a record light conversion efficiency of 8.2% in solvent-free dye-sensitized solar cells.
Perfecting a solar cell by adding imperfections
Nanotechnology is paving the way toward improved solar cells. New research shows that a film of carbon nanotubes may be able to replace two of the layers normally used in a solar cell, with improved performance at a lower cost. Researchers have found a surprising way to give the nanotubes the properties they need: add defects.
Researchers think pink to produce 'green' solar energy
When it comes to producing earth-friendly solar energy, pink may be the new green, according to Ohio State University researchers. Scientists here have developed new dye-sensitized solar cells, that get their pink color from a mixture of red dye and white metal oxide powder in materials that capture light.
Solar energy: Charged for the future
Once regarded as costly and impractical, solar technology is now poised to play a larger role in the future, thanks to new developments that could result in lower costs and improved efficiency.
Nature Research Journals press release
[1] Molecule that induces tumour regression
More Dye-sensitized Solar Cells Current Events and Dye-sensitized Solar Cells News Articles
|
Dye-sensitized Solar Cells by Kuppuswamy Kalyanasundaram (Author) Several forms of thin-film solar cells are being examined as alternatives to silicon-solar cells—one of the most promising technologies is the dye-sensitized solar cell (DSC), with proven efficiencies that approach 11%. This book, which provides a comprehensive look at this promising technology, aims to provide both a graduate level text that brings together the fundamentals of DSC from three perspectives (materials, performance, and mechanistic aspects), as well as to serve as an advanced monograph that summarizes the key advances and lists the technical challenges remaining to be solved. | |
 |
The TiO2/Dye/Electrolyte-Interface in the Dye Sensitized Solar Cell: A Synchrotron Induced Photoelectron Spectroscopy Study by Konrad Schwanitz (Author) In this work it has been attempted for the first time to investigate the complete working electrode (half cell interface: TiO2/dye/electrolyte) of the Dye Sensitized Solar Cell (DSSC) by means of photoelectron spectroscopy. The scope of this work is to investigate the interfacial interactions between the adsorbates and the TiO2 substrate, rather than bulk processes within the substrate or electrolyte. Since the coverage of the dye onto the TiO2 substrate amounts only up to one monolayer, a highly surface sensitive method, as Synchrotron Induced Photoelectron Spectroscopy (SXPS), has been applied to investigate the topological, chemical and especially the electronic interactions within the working electrode interface. |
 |
TiO2 Nanotube Arrays: Synthesis, Properties, and Applications by Craig A. Grimes (Author), Gopal K. Mor (Author) TiO2 Nanotube Arrays: Synthesis, Properties, and Applications is the first book to provide an overview of this rapidly growing field. Vertically oriented, highly ordered TiO2 nanotube arrays are unique and easily fabricated materials with an architecture that demonstrates remarkable charge transfer as well as photocatalytic properties. This volume includes an introduction to TiO2 nanotube arrays, as well as a description of the material properties and distillation of the current research. Applications considered include gas sensing, heterojunction solar cells, water photoelectrolysis, photocatalytic CO2 reduction, as well as several biomedical applications. Written by leading researchers in the field, TiO2 Nanotube Arrays: Synthesis, Properties, and Applications is a valuable... |
|
Solar energy conversion at dye sensitized nanostructured electrodes fabricated by sol-gel processing: Final report by Peter C Searson (Author) |
| © 2009 BrightSurf.com |