Denser computer chips possible with plasmonic lenses that 'fly'

October 23, 2008

Engineers at the University of California, Berkeley, are reporting a new way of creating computer chips that could revitalize optical lithography, a patterning technique that dominates modern integrated circuits manufacturing.

By combining metal lenses that focus light through the excitation of electrons - or plasmons - on the lens' surface with a "flying head" that resembles the stylus on the arm of an old-fashioned LP turntable and is similar to those used in hard disk drives, the researchers were able to create line patterns only 80 nanometers wide at speeds up to 12 meters per second, with the potential for higher resolution detail in the near future.

"Utilizing this plasmonic nanolithography, we will be able to make current microprocessors more than 10 times smaller, but far more powerful," said Xiang Zhang, UC Berkeley professor of mechanical engineering and head of the research team behind this development. "This technology could also lead to ultra-high density disks that can hold 10 to 100 times more data than disks today."

Zhang worked jointly on the project with David Bogy, UC Berkeley professor of mechanical engineering. The study now appears online in Nature Nanotechnology, and is scheduled for the journal's December print issue.

The process of optical lithography shares some of the same principles as film photography, which creates pictures by exposing film in a camera to light, and then developing the film with chemical solutions. In the semiconductor industry, optical lithography is a process in which light is transferred through a mask with the desired circuit pattern onto a photosensitive material, or photoresist, that reacts chemically when exposed. The material then goes through a series of chemical baths to etch the circuit design onto a wafer.

"With optical lithography, or photolithography, you can instantly project a complex circuit design onto a silicon wafer," said Liang Pan, a UC Berkeley graduate student working with Zhang and Bogy, and one of three co-lead authors of the Nature Nanotechnology paper. "However, the resolution possible with this technique is limited by the fundamental nature of light. To get a smaller feature size, you must use shorter and shorter light wavelengths, which dramatically increases the cost of manufacturing. Also, light has a diffraction limit restricting how small it can be focused. Currently, the minimum feature size with conventional photolithography is about 35 nanometers, but our technique is capable of a much higher resolution at a relatively low cost."

The UC Berkeley researchers chose a different approach to overcome the diffraction limit of light. They took advantage of a well-known property of metals: the presence at the surface of free electrons that oscillate when exposed to light. These oscillations, which absorb and generate light, are known as evanescent waves and are much smaller than the wavelength of light.

The engineers designed a silver plasmonic lens with concentric rings that concentrate the light to a hole in the center where it exits on the other side. In the experiment, the hole was less than 100 nanometers in diameter, but it can theoretically be as small as 5 to 10 nanometers. The researchers packed the lenses into a flying plasmonic head, so-called because it would "fly" above the photoresist surface during the lithography process.

Similar flying heads have been developed at UC Berkeley's Computer Mechanics Laboratory, which is directed by Bogy. "Flying heads support the phenomenal advances in data storage in hard disk drives," said Bogy. "They enable the fast speeds and nanometer accuracy required in this potentially new approach to semiconductor manufacturing."

The researchers said the flying head design could potentially hold as many as 100,000 lenses, enabling parallel writing for even faster production.

The researchers compared this flying plasmonic head to the arm and stylus of an LP turntable, with the photoresist surface spinning like a record. Instead of a needle moving along the grooves of a spinning record, however, the flying plasmonic head contains a nanometer-scale optical stylus that "writes" onto the spinning surface of the photoresist without actually touching it.

Because the light from plasmons decays less than 100 nanometers from the metal surface, the photoresist material must be placed very close to the lens. To accommodate this limitation, the researchers designed an air bearing that uses the aerodynamic lift force created by the spinning to help keep the two surfaces a mere 20 nanometers apart.

Air bearings are used to create magnetic tapes and disk drives, but this is the first application for a plasmonic lens.

With this innovative setup, the engineers demonstrated scanning speeds of 4 to 12 meters per second.

"The speed and distances we're talking about here are equivalent to a Boeing 747 flying 2 millimeters above the ground," added Zhang. "Moreover, this distance is kept constant, even when the surface is not perfectly flat."

The researchers pointed out that a typical photolithography tool used for chip manufacturing costs $20 million, and a set of lithography masks can run $1 million. One of the reasons for the great expense is the use of shorter light wavelengths to create higher resolution circuitry. Shorter wavelengths require nontraditional and costly mirrors and lenses.

The system described by the UC Berkeley engineers uses surface plasmons that have much shorter wavelengths than light, yet are excitable by typical ultraviolet light sources with much longer wavelengths. The researchers estimate that a lithography tool based upon their design could be developed at a small fraction of the cost of current lithography tools.

Other alternatives have been developed that can achieve higher resolution than conventional photolithography and without the need for a lithography mask. However, those techniques - electron beam lithography, scanning probe lithography and focused ion-beam lithography - work at a snail's pace compared to the flying plasmonic lens system, said the UC Berkeley researchers.

Zhang noted that the flying head design is not limited to plasmonic lenses. His lab has been developing metamaterials - composite materials capable of bending electromagnetic waves in extraordinary ways - into lenses that can be used for nano-optic imaging and other applications.

"I expect in three to five years we could see industrial implementation of this technology," said Zhang. "This could be used in microelectronics manufacturing or for optical data storage and provide resolution that is 10 to 20 times higher than current blu-ray technology."

The other co-lead authors of the study are Werayut Srituravanich, a former Ph.D. student in Zhang's lab and currently a lecturer in mechanical engineering at Chulalongkorn University in Thailand, and Yuan Wang, a UC Berkeley graduate student in mechanical engineering. The study was also co-authored by Cheng Sun, a former graduate student in Zhang's lab and currently an assistant professor in mechanical engineering at Northwestern University.

This work was supported by the National Science Foundation Center for Scalable and Integrated Nano-Manufacturing.

University of California, Berkeley

---

---

	Nonimaging Fresnel Lenses: Design and Performance of Solar Concentrators (Springer Series in Optical Sciences) by Ralf Leutz (Author), Akio Suzuki (Author) A detailed and comprehensive account of the engineering of the world’s first nonimaging Fresnel lens solar concentrator. The book closes a gap in solar concentrator design, and describes nonimaging refractive optics and its numerical mathematics. The book shows the reader how to find his or her own optical solution using the rules and methodologies covering the design and the assessment of the nonimaging lens.
	Focusing light on nanoscale: A novel plasmonic-lens design. by Shantha Vedantam (Author) Surface plasmons are oscillations of the conduction charges at a metal-dielectric interface. The symmetric mode of the surface plasmonic oscillation has no cut-off for propagation. A thin layer of dielectric sandwiched between two thick layers of metal can support plasmonic modes with large propagation constant and small group velocity. Further, surface plasmons can be easily excited by photons. These attributes of the surface plasmons give way to the design of a circularly symmetric three dimensional nanoscopic structure that can be used to focus down the energy of a plasmon to a very small volume, much beyond the conventional diffraction limit. Analysis of metal-optics on the sub-wavelength scale using...
	Darkfield imaging with a plasmonic focusing lens: Antenna theory for near-field scanning optical microscopes. by Japeck Tang (Author) It is widely known that optical imaging is not strictly limited by the Rayleigh limit. Recently, a dimple-shaped plasmonic lens has been fabricated for focusing light to the nanoscale. This dissertation will begin with a discussion of the design, fabrication, and experimental measurements of this plasmonic dimple lens. However, one of the drawbacks of the plasmonic dimple lens is that it is an open structure, so light from the input side is scattered and introduces noise into the output of the device. This background noise may be acceptable in some applications that have an inherent threshold, such as for Heat Assisted Magnetic Recording (HAMR). In other applications, it may be desirable to have low background noise, such as for sensitive optical measurements, e.g. Near-field Scanning...
	Nanofabrication Handbook by Stefano Cabrini (Editor), Satoshi Kawata (Editor) While many books are dedicated to individual aspects of nanofabrication, there is no single source that defines and explains the total vision of the field. Filling this gap, Nanofabrication Handbook presents a unique collection of new and the most important established approaches to nanofabrication. Contributors from leading research facilities and academic institutions around the world define subfields, offer practical instructions and examples, and pave the way for future research. Helping readers to select the proper fabricating technique for their experiments, the book provides a broad vision of the most critical problems and explains how to solve them. It includes basic definitions and introduces the main underlying concepts of nanofabrication. The book also discusses the major...
	Basic Principles of Fresnel Antenna Arrays (Lecture Notes in Electrical Engineering) by Igor V. Minin (Author), Oleg V. Minin (Author) Antennas represent a critical technology in any of these wireless systems. Not only do they directly affect the received power of the system, they are also typically the largest and most visible part. Recently, the need for low-cost, low-profile, and lightweight antenna in the frequency range of the microwave/millimeter wave/THz band has regained momentum. "Basic Principles of Fresnel Antenna Arrays" provides us a with the basics of the various Fresnel Antenna approaches, in order to achieve low-cost, low-profile, and lightweight antenna in the microwave/millimeter wave band. A potential solution of the antenna problem lies in using lens technology in an array. The Fresnel zone plate lens (FZPL) antenna is in particular an interesting candidate for the array element. The limiting...
	High-Efficient Low-Cost Photovoltaics: Recent Developments (Springer Series in Optical Sciences) by Vesselinka Petrova-Koch (Editor), Rudolf Hezel (Editor), Adolf Goetzberger (Editor) A bird's-eye view of the development and problems of recent photovoltaic cells and systems and prospects for Si feedstock is presented. High-efficient low-cost PV modules, making use of novel efficient solar cells (based on c-Si or III-V materials), and low cost solar concentrators are in the focus of this book. Recent developments of organic photovoltaics, which is expected to overcome its difficulties and to enter the market soon, are also included.
	Laser Diode Beam Basics, Manipulations and Characterizations (SpringerBriefs in Physics) by Haiyin Sun (Author) Many optical design technical books are available for many years which mainly deal with image optics design based on geometric optics and using sequential raytracing technique. Some books slightly touched laser beam manipulation optics design. On the other hand many books on laser diodes have been published that extensively deal with laser diode physics with little touching on laser diode beam manipulations and characterizations. There are some internet resources dealing with laser diode beams. However, these internet resources have not covered enough materials with enough details on laser diode beam manipulations and characterizations. A technical book concentrated on laser diode beam manipulations and characterizations can fit in to the open and provide useful information to laser diode...
	Laser Material Processing by William M. Steen (Author), Jyotirmoy Mazumder (Author), Kenneth G. Watkins (Contributor) The informal style of Laser Material Processing (4th Edition) will guide you smoothly from the basics of laser physics to the detailed treatment of all the major materials processing techniques for which lasers are now essential. • Helps you to understand how the laser works and to decide which laser is best for your purposes. • New chapters on laser physics, drilling, micro- and nanomanufacturing and biomedical laser processing reflect the changes in the field since the last edition, updating and completing the range of practical knowledge about the processes possible with lasers already familiar to established users of this well-known text. • Provides a firm grounding in the safety aspects of laser use. • Now with end-of-chapter exercises to help students assimilate information...
	Systems Engineering for Microscale and Nanoscale Technologies by M. Ann Garrison Darrin (Editor), Janet L. Barth (Editor) To realize the full potential of micro- and nanoscale devices in system building, it is critical to develop systems engineering methodologies that successfully integrate stand-alone, small-scale technologies that can effectively interface with the macro world. So how do we accomplish this? Systems Engineering for Microscale and Nanoscale Technologies is perhaps the first handbook to concentrate on the use of systems engineering at the micro and nano levels. One major roadblock to this process is a generally limited understanding of exactly how to apply systems engineering principles and management processes to the integration of newer, small-scale technologies. Focusing on this problem of consolidating disciplines, contributors illustrate the interdependence between...
	Engineering Optics (Springer Series in Optical Sciences) by Keigo Iizuka (Author) Engineering Optics is a book for students who want to apply their knowledge of optics to engineering problems, as well as for engineering students who want to acquire the basic principles of optics. It covers such important topics as optical signal processing, holography, tomography, holographic radars, fiber optical communication, electro- and acousto-optic devices, and integrated optics (including optical bistability). Practical examples, such as the video disk, the Fresnel zone plate, and many more, appear throughout the text, together with numerous solved exercises. There is an entirely new section in this updated edition on 3-D imaging.