Advanced measurement technology for future semiconductor devices

January 25, 2021

1. Key points of the work2. Overview of the work

The β-Ga2O3 ultra-wide bandgap (UWBG) semiconductor [1,2] could revolutionize the power electronics industry with its superior material properties for efficient power conversion in comparison to current commercial semiconductors such as silicon carbide and gallium nitride (Figure 1). To develop electronic applications, material properties in the millimeter and terahertz wave regions must be elucidated. A research group including Associate Professor Makoto Nakajima, Verdad C. Agulto, Valynn Katrine Mag-usara of Osaka University, Toshiyuki Iwamoto of Nippo Precision Co., Ltd., Professor Yoshinao Kumagai, Associate Professor Hisashi Murakami, and Assistant Professor Ken Goto of Tokyo University of Agriculture and Technology employed a noninvasive technique called terahertz time-domain spectroscopy (THz-TDS) [3] to investigate β-Ga2O3 materials using THz waves [4] and demonstrated the viability of this tool for the practical evaluation of β-Ga2O3-based devices.

THz-TDS is used to measure the permittivity of a material--a fundamental property that describes how much electrical energy the material can store and is an important parameter relevant to power devices. The researchers determined the permittivity of β-Ga2O3 in the THz region using the THz-TDS technique. From the permittivity, they were also able to extract the electrical properties such as carrier density and resistivity with an accuracy that is comparable to conventional albeit invasive measurement methods used in the semiconductor industry. The researchers believe that the application of THz-TDS in semiconductor characterization would be advantageous towards the rapid development of β-Ga2O3 materials for future power devices.

The article, "Anisotropic complex refractive index of β-Ga2O3 bulk and epilayer evaluated by terahertz time-domain spectroscopy," was published online in Applied Physics Letters on January 25, 2021, 11:00 AM Eastern Standard Time (January 26, 2021, 1:00 AM Japan Standard Time) at DOI: https://doi.org/10.1063/5.0031531

3. Details of the work

Terahertz frequencies (about 100 GHz to 10 THz) lie between the microwave and infrared regions of the electromagnetic spectrum, with the frequency band around 100 GHz being considered as an ultra-high frequency region for the next-generation communication band also known as Beyond 5G/6G. By studying the interaction of semiconductors with THz radiation, various information about the semiconductor properties can be acquired. The THz-TDS investigation of β-Ga2O3 materials--semi-insulating bulk crystal and doped homoepitaxial film-- was led by Associate Professor Makoto Nakajima of the Institute of Laser Engineering. The transmission of THz beam through the β-Ga2O3 materials was measured using the equipment developed by Nippo Precision Co. Ltd. (PNP) called Tera Prospector [5]. Since β-Ga2O3 is an anisotropic crystal (i.e., its properties vary along different crystal axes), the transmission measurements were done along two different crystal directions that are parallel to the a and b crystal axes. By evaluating the measured transmission, fundamental material properties such as the anisotropic complex refractive index [6] in the THz region were determined. The complex refractive index is in turn related to the material's permittivity.

Using the THz-TDS technique, the researchers succeeded in obtaining the complex refractive index spectra in the terahertz band which is an ultra-high frequency region. Figure 2 shows the complex refractive index of the semi-insulating bulk crystal and the doped homoepitaxial film (or epilayer) in the THz region measured by THz-TDS. The semi-insulating β-Ga2O3 single crystal sample exhibits increasing refractive index with increasing frequency, which indicates the presence of phonon absorption in the infrared region. On the other hand, the n-type β-Ga2O3 epitaxial film exhibits increasing refractive index with decreasing frequency which is different from the semi-insulating sample. This increase in refractive index in the low-frequency side indicates absorption depending on the amount of carrier density in β-Ga2O3. By evaluating this low-frequency region, it is possible to obtain information on carrier density, carrier scattering time, and mobility. The results are summarized in Table I. It was found that the refractive index at 0.2 THz is 3.165 along a-axis and 3.231 along b-axis. The researchers used the Drude-Lorentz model [7] to analyze the experimental data. Using this model, they extracted the static permittivity [8] of β-Ga2O3 as well as the electrical properties of the doped epilayer. The static permittivity (dielectric constant at 0 Hz) was found to be 10.02 along a-axis and 10.43 along b-axis. A carrier density of 4.6 x 1017 cm-3, a mobility of 100 cm2 V-1 s-1, and a resistivity of 0.13 Ωcm were obtained for the n-type β-Ga2O3 epitaxial film. In device fabrication, the electrical properties of semiconductor films are tuned via doping (intentional addition of impurities). As such, the electrical characterization of doped films is imperative. Conventional electrical characterization techniques include the Hall method [9], where attachment of metal contacts is necessary, and capacitance-voltage (CV) measurements [10], which sometimes use toxic mercury (Hg) probes. These techniques, however, are becoming impractical for rapid device development because of their invasive nature and relatively time-consuming measurement. In this regard, THz-TDS is an attractive alternative to conventional methods because it is nondestructive and more straightforward as it doesn't necessitate any type of electrical contacts or probes. By modelling the experimental refractive index derived from the THz-TDS measurements, the researchers were able to extract the electrical properties of the doped epilayer with good accuracy. The obtained electrical properties are closely comparable to the results of the conventional Hall measurement (Table I). These findings demonstrate that THz-TDS is a reliable and viable technique to replace conventional methods for the electrical characterization of β-Ga2O3 semiconductors.

In this work, the researchers reported the fundamental properties of β-Ga2O3 in the THz frequency region. Moreover, they demonstrated the noninvasive evaluation of electrical properties using the THz-TDS technique. Their findings have significant contribution to the rapid development of β-Ga2O3 devices and applications.
-end-
4. Glossary

(1) Gallium oxide (Ga2O3)

Ga2O3 belongs to a group of materials referred to as ultrawide bandgap semiconductors. It exists in various forms, but the most stable one is the β-Ga2O3 crystal structure. Research on β-Ga2O3 materials is a highly active area nowadays because the β-Ga2O3 semiconductor shows significant potential for high-power and high-voltage devices.

(2) Ultra-wide bandgap (UWBG) semiconductors

Semiconductors are often categorized according to their bandgap--a key property that determines their uses and applications. The conventional silicon (Si) semiconductor has a bandgap of 1.12 eV and is commonly used in integrated circuits. Wide-bandgap semiconductors have a larger bandgap, e.g., gallium nitride (GaN) and silicon carbide (SiC) which have bandgaps of 3.4 eV and 3.26 eV, respectively. Semiconductors with wider bandgaps are used in devices that need to operate at higher voltages and temperatures. UWBG semiconductors are those that have a bandgap larger than that of GaN, like β-Ga2O3 which has a bandgap of ~4.8 eV. Such materials are attractive for high-power and high-voltage applications.

(3) Terahertz time-domain spectroscopy (THz-TDS)

THz-TDS is a technique that probes material properties using terahertz waves. Unlike ultraviolet light or x-rays, terahertz radiation is nondestructive due to its lower energies. THz-TDS is widely used to characterize the dielectric and electrical properties of semiconductors and other materials in the far-infrared region.

(4) Terahertz wave (THz wave)

THz waves refer to electromagnetic waves with frequencies in the order of 1012 Hz, specifically in the wavelength region between 3 mm and 30 μm (0.1~10 THz). Aside from their scientific applications like material analysis, THz waves can also be used in technologies such as medical imaging, security screening, and telecommunications. With frequencies higher than radio waves, THz waves can pave the way for high-frequency operation devices and high-speed, ultra-high bandwidth communications. As such, THz is considered key to communication technologies beyond 5G/6G.

(5) Tera Prospector

Tera Prospector is a general-purpose THz time-domain spectrometer developed by Nippo Precision Co., Ltd. The complex refractive index/permittivity spectra in the terahertz region can be measured accurately using this equipment. In addition to Ga2O3, it can be used for other semiconductors such as Si, SiC and GaN. https://terahertzwave.com/en/

(6) Complex refractive index

The complex refractive index is a material property that describes how light propagates through the material. The real part is the refractive index which is related to the speed of propagation, while the imaginary part is the extinction coefficient which indicates how strongly the light is attenuated as it propagates in the material. Light is attenuated when part of the energy is absorbed by the crystal atoms (phonon absorption) or by the free electrons in the material (free carrier absorption). The complex refractive index can also be expressed in terms of permittivity as a function of frequency.

(7) Drude-Lorentz model

The Drude-Lorentz model quantifies the dependence of the complex refractive index and permittivity on the frequency of light, taking into account the effects of phonons and free carriers. This model is commonly used in evaluating semiconductor materials.

(8) Static permittivity

The static permittivity refers to the permittivity at zero frequency or 0 Hz.

(9) Hall measurement

Hall measurement is a conventional characterization technique to measure the electrical properties of semiconductors. In the Hall method using van der Pauw configuration, current is applied and voltage is measured with the use metal contacts.

(10) Capacitance-voltage (CV) measurements

CV measurements are another conventional technique used to characterize the electrical properties of semiconductors and devices. In this measurement, voltage is applied then the capacitance of the material is measured with varying voltage with the use of electrodes.

About Osaka University

Osaka University was founded in 1931 as one of the seven imperial universities of Japan and is now one of Japan's leading comprehensive universities with a broad disciplinary spectrum. This strength is coupled with a singular drive for innovation that extends throughout the scientific process, from fundamental research to the creation of applied technology with positive economic impacts. Its commitment to innovation has been recognized in Japan and around the world, being named Japan's most innovative university in 2015 (Reuters 2015 Top 100) and one of the most innovative institutions in the world in 2017 (Innovative Universities and the Nature Index Innovation 2017). Now, Osaka University is leveraging its role as a Designated National University Corporation selected by the Ministry of Education, Culture, Sports, Science and Technology to contribute to innovation for human welfare, sustainable development of society, and social transformation. Website: https://resou.osaka-u.ac.jp/en

Osaka University

Related Semiconductor Articles from Brightsurf:

Blue phosphorus: How a semiconductor becomes a metal
Blue phosphorus, an atomically thin synthetic semiconductor, becomes metallic as soon as it is converted into a double layer.

A new method to measure optical absorption in semiconductor crystals
Tohoku University researchers have revealed more details about omnidirectional photoluminescence (ODPL) spectroscopy - a method for probing semiconducting crystals with light to detect defects and impurities.

Medical robotic hand? Rubbery semiconductor makes it possible
A medical robotic hand could allow doctors to more accurately diagnose and treat people from halfway around the world, but currently available technologies aren't good enough to match the in-person experience.

Laser allows solid-state refrigeration of a semiconductor material
A team from the University of Washington used an infrared laser to cool a solid semiconductor by at least 20 degrees C, or 36 F, below room temperature, as they report in a paper published June 23 in Nature Communications.

Scientists create smallest semiconductor laser
An international team of researchers announced the development of the world's most compact semiconductor laser that works in the visible range at room temperature.

Clemson researcher's novel MOF is potential next-gen semiconductor
Clemson professor Sourav Saha demonstrated a novel double-helical metal organic framework architecture in a partially oxidized form that conducts electricity, potentially making it a next-generation semiconductor.

A gold butterfly can make its own semiconductor skin
A nanoscale gold butterfly provides a more precise route for growing/synthesizing nanosized semiconductors that can be used in nano-lasers and other applications.

Scientists pioneer new generation of semiconductor neutron detector
In a new study, scientists have developed a new type of semiconductor neutron detector that boosts detection rates by reducing the number of steps involved in neutron capture and transduction.

Scientists see defects in potential new semiconductor
A research team has reported seeing, for the first time, atomic scale defects that dictate the properties of a new and powerful semiconductor.

Bending an organic semiconductor can boost electrical flow
Slightly bending semiconductors made of organic materials can roughly double the speed of electricity flowing through them and could benefit next-generation electronics such as sensors and solar cells, according to Rutgers-led research.

Read More: Semiconductor News and Semiconductor Current Events
Brightsurf.com is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon.com.