MIT researchers build first germanium laser

February 04, 2010

MIT researchers have demonstrated the first laser built from germanium that can emit wavelengths of light useful for optical communications. It's also the first germanium laser to operate at room temperature. Unlike the materials typically used in lasers, germanium is easy to incorporate into existing processes for manufacturing silicon chips. So the result could prove an important step toward computers that move data -- and maybe even perform calculations -- using light instead of electricity.

More fundamentally, the researchers have shown that, contrary to prior belief, a class of materials called indirect-band-gap semiconductors can yield practical lasers. "The laser is just totally new physics," says Lionel Kimerling, the Thomas Lord Professor of Materials Science and Engineering, whose Electronic Materials Research Group developed the germanium laser.

As chips' computational capacity increases, they need higher-bandwidth connections to send data to memory. But conventional electrical connections will soon become impractical, because they'll require too much power to transport data at ever higher rates. Transmitting data with lasers -- devices that concentrate light into a narrow, powerful beam -- could be much more power efficient, but it requires a cheap way to integrate optical and electronic components on silicon chips.

The lasers used in today's communication systems are made from expensive materials such as gallium arsenide, and they have to be constructed separately and then grafted onto chips, which is more expensive and time consuming than building them directly on silicon. Integrating germanium into the manufacturing process, however, is something that almost all major chip manufacturers have already begun to do, since adding germanium increases the speed of silicon chips.

How they did it: In a semiconductor crystal, an excited electron -- one that's had energy added to it -- will break free and enter the so-called conduction band, where it can move freely around the crystal. But in fact, an electron in the conduction band can be in one of two states. If it's in the first state, and it falls out of the conduction band, it will release its extra energy as a photon. If it's in the second state, it will release its energy in other ways, such as heat.

In direct-band-gap materials, the first state -- the photon-emitting state -- is a lower-energy state than the second state; in indirect-band-gap materials, it's the other way around. An excited electron will naturally occupy the lowest-energy state it can find. So in direct-band-gap materials like gallium arsenide, excited electrons tend to go into the photon-emitting state; in indirect-band-gap materials like germanium, they don't.

Kimerling's group describes its results in a forthcoming paper in Optics Letters. The primary investigator on the project was Jurgen Michel, the principal research associate in the group, and the lead author was postdoc Jifeng Liu. Kimerling and grad students Xiaochen Sun and Rodolfo Camacho-Aguilera are also coauthors.

The researchers used two strategies to coax excited germanium electrons into the higher-energy, photon-emitting state. The first is a technique common in chip manufacture called "doping," in which atoms of some contaminant are added to a semiconductor crystal. The group doped its germanium with phosphorous, which has five outer electrons, where germanium has only four. The extra electron fills up the lower-energy state in the conduction band, causing excited electrons to, effectively, spill over into the higher-energy, photon-emitting state.

The second strategy was to lower the energy difference between the two conduction-band states, so that excited electrons would be more likely to spill over into the photon-emitting state. The researchers did that by adapting another technique common in the chip industry: they "strained" the germanium -- or pried its atoms slightly farther apart than they would be naturally -- by growing it directly on top of a layer of silicon.

Next steps: The researchers need to find a way to increase the concentration of phosphorus atoms in the doped germanium. That should increase the power efficiency of the lasers, making them more attractive as sources of light for optical data connections.
-end-
Source: "A Ge-on-Si laser operating at room temperature," Jifeng Liu, Xioachen Sun, Rodolfo Camacho-Aguilera, Lionel C. Kimerling, and Jurgen Michel, forthcoming in Optics Letters, published online 26 January 2010. To view the paper see: http://www.opticsinfobase.org/ol/upcoming_pdf.cfm?id=119019

Funding: The Si-Based-Laser Initiative of the Multidisciplinary University Research Initiative (MURI), sponsored by the Air Force Office of Scientific Research (AFOSR)

Massachusetts Institute of Technology

Related Laser Articles from Brightsurf:

Laser technology: New trick for infrared laser pulses
For a long time, scientists have been looking for simple methods to produce infrared laser pulses.

Sensors get a laser shape up
Laser writing breathes life into high-performance sensing platforms.

Laser-powered nanomotors chart their own course
The University of Tokyo introduced a system of gold nanorods that acts like a tiny light-driven motor, with its direction of motion is determined by the orientation of the motors.

What laser color do you like?
Researchers at the National Institute of Standards and Technology (NIST) and the University of Maryland have developed a microchip technology that can convert invisible near-infrared laser light into any one of a panoply of visible laser colors, including red, orange, yellow and green.

Laser technology: The Turbulence and the Comb
While the light of an ordinary laser only has one single, well-defined wavelength, a so-called ''frequency comb'' consists of different light frequencies, which are precisely arranged at regular distances, much like the teeth of a comb.

A laser for penetrating waves
The 'Landau-level laser' is an exciting concept for an unusual radiation source.

Laser light detects tumors
A team of researchers from Jena presents a groundbreaking new method for the rapid, gentle and reliable detection of tumors with laser light.

The first laser radio transmitter
For the first time, researchers at Harvard School of Engineering have used a laser as a radio transmitter and receiver, paving the way for towards ultra-high-speed Wi-Fi and new types of hybrid electronic-photonic devices.

The random anti-laser
Scientists at TU Wien have found a way to build the 'opposite' of a laser -- a device that absorbs a specific light wave perfectly.

Laser 'drill' sets a new world record in laser-driven electron acceleration
Combining a first laser pulse to heat up and 'drill' through a plasma, and another to accelerate electrons to incredibly high energies in just tens of centimeters, scientists have nearly doubled the previous record for laser-driven particle acceleration at Berkeley Lab's BELLA Center.

Read More: Laser News and Laser Current Events
Brightsurf.com is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon.com.