Nav: Home

Avoiding the crack of doom

February 25, 2019

Just as a journey of 1,000 miles begins with a single step, the deformations and fractures that cause catastrophic failure in materials begin with a few molecules torn out of place. This in turn leads to a cascade of damage at increasingly larger scales, culminating in total mechanical breakdown. That process is of urgent interest to researchers studying how to build high-strength composite materials for critical components ranging from airplane wings and wind-turbine blades to artificial knee joints.

Now scientists from the National Institute of Standards and Technology (NIST) and their colleagues have devised a way to observe the effects of strain at the single-molecule level by measuring how an applied force changes the three-dimensional alignment of molecules in the material.

The technique uses single-molecule, super-resolution optical microscopy, which can resolve objects in the range of 20 nanometers (billionths of a meter)--about one-tenth the size of what can be seen at the sharpest focus with a conventional optical microscope. The new method examines a polymer doped with fluorescent molecules that emit light of one wavelength when they are illuminated with light of another wavelength. An image of the emitted light reveals not only a molecule's location, but also its orientation horizontally and vertically.

The super-resolution microscope, development of which won the 2014 Nobel Prize in Chemistry, has been widely employed for biomedical applications. "But we started wondering what you could do with it in the materials area," said NIST scientist J. Alexander Liddle. "That is, how can we see what is happening at the molecular level at the very earliest stages of deformation or damage? If those mechanisms can be understood, researchers may be able to design better composite materials that can inhibit failure."

Composite materials are used throughout industry to increase strength and decrease weight. For example, half the material by weight in a Boeing 787 airframe is carbon fiber-reinforced plastic and other composites.

For many such materials, it is difficult to see the early onset of damage because there are no visible markers to track its effects. To provide those markers in their experiment, the researchers used a very thin film of a polymer found in Lucite and Plexiglas that had been doped with thousands of fluorescent molecules. Initially, the polymer was unstressed, and the embedded fluorescent molecules were in completely random orientations in three dimensions. Then the scientists applied force to the polymer, deforming it in a controlled specific direction. As the polymer was strained, the embedded fluorescent molecules were carried along with the deformation, losing their random orientation and lining up with the path of the damage. That path was made visible by observing the pattern of emitted light from the embedded fluorescent molecules, which acted like a series of little flashlights pointing the way.

Prior to the experiment, the scientists used a mathematical model that predicted how light would look when emitted by molecules in different 3D alignments. When they illuminated the fluorescent molecules and made images of the emitted light, the results matched the model. After about 10,000 cycles of illumination, a telltale pattern emerged showing the extent of deformation.

"It's sort of like a pointillist painting, where individual dots build up to form a shape," Liddle said.

In addition to the technique's clear relevance to the design of essential composite materials, there might also be applications in medicine.

"Let's say you have a new bioimplant--for example, a knee replacement," said Mitchell Wang, now at Northwestern University, who worked on the experiment while at NIST. "To make it biocompatible, it will likely be made of soft polymers, but you also want the device to have excellent mechanical properties. You want it to operate easily while also being stiff and tough. This technique could help inform design so the materials used have excellent mechanical strength."

There are many avenues for future research. "This technique was a post-mortem study, in that we could view the damage in a material after it already happened," Wang said. "The next step might be to learn how to perform this work in real time, to watch not only where the damage is happening, but when."

Liddle's team is also developing an improved imaging technique. It involves making two simultaneous image sets--one on each side of the doped polymer. On one side, imaging is produced by the method described above. On the other, a separate lens gathers fluorescent light from the material and divides it into four different polarizations in individual channels. Because the polarization of the emitted light is affected by the orientation of the fluorescent molecules, "if you measure the ratios of the intensity in each channel, you can figure out which direction the molecule is pointing," Liddle said. "That would give us an independent measure of orientation."

In addition, the scientists hope to improve resolution by a factor of about five--allowing them to image areas as small as a few nanometers. This could be accomplished by increasing the brightness of the fluorescent molecules, perhaps by reducing their exposure to oxygen, which shuts off fluorescence.

Meanwhile, Liddle said, "it still amazes me that I can look at this little bright spot in a microscope and know within five or ten nanometers where it is and also know, within a few degrees, in which direction it's pointing."
-end-
In addition to NIST scientists, researchers at the University of Maryland NanoCenter contributed to the experiment and journal article.

Paper: M. Wang, J.M Marr, M. Davanco, J.W. Gilman and J.A. Liddle. Nanoscale deformation in polymers revealed by single-molecule super-resolution location - orientation microscopy. Materials Horizons. Published online January 30, 2019. DOI: 10.1039/c8mh01187g

National Institute of Standards and Technology (NIST)

Related Microscope Articles:

Microscope can scan tumors during surgery and examine cancer biopsies in 3-D
A new UW microscope could provide accurate real-time results during cancer-removal surgeries, potentially eliminating the 20 to 40 percent of women who have to undergo multiple lumpectomy surgeries because cancerous breast tissue is missed the first time around.
Next-gen steel under the microscope
Next-generation steel and metal alloys are a step closer to reality, thanks to an international research project involving a University of Queensland scientist.
Engineers shrink microscope to dime-sized device
Researchers at The University of Texas at Dallas have created an atomic force microscope on a chip, dramatically shrinking the size -- and, hopefully, the price tag -- of a high-tech device commonly used to characterize material properties.
Protein research: The computer as microscope
Using a combination of infrared spectroscopy and computer simulation, researchers at Ruhr-Universit├Ąt Bochum have gained new insights into the workings of protein switches.
New microscope chemically identifies micron-sized particles
A team from MIT Lincoln Labs have developed a microscope that can chemically identify individual micron-sized particles.
The self-driving microscope
Researchers develop a combination of software and hardware for adaptive live imaging of large living organisms.
Smart microscope adapts to changes in live specimens
HHMI/Janelia Research Campus scientists have developed the first adaptive light-sheet microscope -- a smart microscope that continuously analyzes and adapts to dynamic changes in a specimen and thereby improves spatial resolution.
Nanowires as sensors in new type of atomic force microscope
A new type of atomic force microscope (AFM) uses nanowires as tiny sensors.
Smartphone microscope creates interactive tool for microbiology
An easily assembled smartphone microscope provides new ways of interacting with and learning about common microbes.
Microscope imaging system integrates virtual reality technology
CaptiView is a microscope image injection system that overlays critical virtual reality imaging directly onto the brain when viewed through the eyepiece during surgery.

Related Microscope Reading:

Best Science Podcasts 2019

We have hand picked the best science podcasts for 2019. Sit back and enjoy new science podcasts updated daily from your favorite science news services and scientists.
Now Playing: TED Radio Hour

Jumpstarting Creativity
Our greatest breakthroughs and triumphs have one thing in common: creativity. But how do you ignite it? And how do you rekindle it? This hour, TED speakers explore ideas on jumpstarting creativity. Guests include economist Tim Harford, producer Helen Marriage, artificial intelligence researcher Steve Engels, and behavioral scientist Marily Oppezzo.
Now Playing: Science for the People

#524 The Human Network
What does a network of humans look like and how does it work? How does information spread? How do decisions and opinions spread? What gets distorted as it moves through the network and why? This week we dig into the ins and outs of human networks with Matthew Jackson, Professor of Economics at Stanford University and author of the book "The Human Network: How Your Social Position Determines Your Power, Beliefs, and Behaviours".