Nav: Home

Estimating the glass transition temperature for polymers in 'confined geometries'

March 21, 2017

WASHINGTON, D.C., March 21, 2017 -- Polymers are used for myriad applications today, and perhaps the most important property that dictates which polymer is chosen for a given application is its "glass transition temperature." Many industrial polymers possess an irregular molecular structure that makes it impossible for them to crystallize. As a polymer material cools from a high temperature above its glass transition temperature, it morphs from a liquid to a glass when the transition temperature is reached.

While a polymer material has an amorphous, liquidlike structure in its glassy state, the mobility of the molecules is so low that they're essentially frozen. So many hard plastics are, in fact, glassy. Polystyrene, for example, has a glass transition temperature of about 100 C -- at room temperature it behaves like a solid material. But as its temperature approaches the glass transition temperature, polystyrene's mechanical properties change drastically.

This makes the ability to approximate glass transitions for confined geometries in polymers highly desirable. And now, as a group of researchers from the University of New Mexico and New Mexico Institute of Mining and Technology report in this week's issue of the Journal of Chemical Physics, from AIP Publishing, they've developed a simple formula to do just that.

"With the development of nanotechnology, polymers have found many applications that require their use in 'confined geometries' such as narrow channels, small pores, and thin films," explained the study's co-author John Curro, an adjunct professor at New Mexico Institute of Mining and Technology

Over the past 20 years, experiments have shown that when polymers are used in a confined geometry, their glass transition "isn't necessarily the same as for the corresponding 'unconfined' or bulk polymer," Curro said. "It's usually lowered, as is the case for free-standing films with two free surfaces, but it can also increase for liquids against strongly attracting substrates."

The shift in glass transition depends sensitively on film thickness -- the thinner the film the greater the effect. "This shift can be extraordinarily large," Curro said. "For example, the glass transition temperature of a 20-nanometer polystyrene film has been measured as much as 70 C lower than bulk polystyrene. Clearly, this thin film of polystyrene is no longer a hard plastic material."

As far as potential applications, "the fact that polymer properties in confined geometries are different than in bulk could have important implications for photolithography, nanocomposites, micromachines, and lab-on-a-chip devices," Curro said.

So why is the glass transition of a confined polymer different than that of its corresponding bulk material?

"We hypothesized that it's due to a density effect," Curro said. "In an unconfined bulk liquid, the density is constant throughout the sample. By contrast, a confined liquid's density of molecules is nonuniform because of constraints imposed by geometry."

A freestanding film's density, for example, is essentially zero at the two surfaces but increases to near the bulk density within the center. "Since the glass transition temperature depends strongly on density, we expect the local glass transition temperature to likewise vary throughout the film," Curro said. "In a lab experiment, the measured glass transition temperature represents the average response of the material within the film. The average density of a freestanding film is generally different than its bulk density, and it follows that the glass transition temperatures will also be different."

So the group explored whether the glass transition temperature of a confined liquid would be the same as a hypothetical bulk polymer -- not at its normal bulk density, but rather at a density equal to the average density of the confined polymer.

To put it to the test, they wanted to measure both the density profile and glass temperature on the same thin film. Such measurements would be difficult to carry out in the laboratory.

"Our approach was to use 'molecular dynamics' computer simulations to study thin liquid films consisting of short chain molecules," Curro said. "We also performed computer simulations of the corresponding bulk system. This allowed us to compare the glass transition temperatures of thin films of various thicknesses with the bulk glass transition temperature on the same model chains."

For computational efficiency, the group used an idealized bead-spring model of 10 beads to represent the molecules. By doing so, they "established a connection between the glass transition temperatures of a polymer in a constrained geometry and the corresponding bulk polymer," Curro said. "This allowed us to develop a simple formula to estimate the glass transition of a confined liquid from the bulk glass transition temperature and a knowledge of the density profile of the confined system."

It's also important to note that the group's results only apply to low molecular weight polymers and small molecule glasses.

"Subtle molecular weight effects are observed experimentally at high molecular weights when the average chain size is comparable to the film thickness, so high molecular weight will be a topic for future investigations," Curro said.
-end-
The article, "The glass transition temperature of thin films: A molecular dynamics study for a bead-spring model," is authored by Craig Stevenson, John G. Curro and John D. McCoy. The article will appear in The Journal of Chemical Physics March 21, 2017 (DOI: 10.1063/1.4977521). After that date, it can be accessed at http://aip.scitation.org/doi/full/10.1063/1.4977521.

ABOUT THE JOURNAL

The Journal of Chemical Physics publishes concise and definitive reports of significant research in the methods and applications of chemical physics. See http://jcp.aip.org.

American Institute of Physics

Related Polymers Articles:

Fluorescent technique brings aging polymers to light
Modern society relies on polymers, such as polypropylene or polyethylene plastic, for a wide range of applications, from food containers to automobile parts to medical devices.
Polymers to the rescue! Saving cells from damaging ice
Research published in the Journal of the American Chemical Society by University of Utah chemists Pavithra Naullage and Valeria Molinero provides the foundation to design efficient polymers that can prevent the growth of ice that damages cells.
Mixing the unmixable -- a novel approach for efficiently fusing different polymers
Cross-linked polymers are structures where large molecular chains are linked together, allowing exceptional mechanical properties and chemical resistance to the final product.
Theoretical tubulanes inspire ultrahard polymers
Rice University engineers print 3D blocks based on theoretical tubulanes and find they're nearly as hard as diamond.
New synthesis method yields degradable polymers
MIT chemists have come up with a way to make certain drug-delivery polymers more readily degradable by adding a novel type of building block to the polymer backbone.
Bottom-up synthesis of crystalline 2D polymers
Scientists at TU Dresden and Ulm University have succeeded in synthesizing sheet-like 2D polymers by a bottom-up process for the first time.
Secret messages hidden in light-sensitive polymers
Scientists from the CNRS and Aix-Marseille Université have recently shown how valuable light-sensitive macromolecules are: when exposed to the right wavelength of light, they can be transformed so as to change, erase or decode the molecular message that they contain.
Successful application of machine learning in the discovery of new polymers
As a powerful example of how artificial intelligence (AI) can accelerate the discovery of new materials, scientists in Japan have designed and verified polymers with high thermal conductivity -- a property that would be the key to heat management, for example, in the fifth-generation (5G) mobile communication technologies.
How to capture waste heat energy with improved polymers
By one official estimate, American manufacturing, transportation, residential and commercial consumers use only about 40 percent of the energy they draw on, wasting 60 percent.
Researchers can now predict properties of disordered polymers
Thanks to a team of researchers from the University of Illinois at Urbana-Champaign and the University of Massachusetts Amherst, scientists are able to read patterns on long chains of molecules to understand and predict behavior of disordered strands of proteins and polymers.
More Polymers News and Polymers Current Events

Trending Science News

Current Coronavirus (COVID-19) News

Top Science Podcasts

We have hand picked the top science podcasts of 2020.
Now Playing: TED Radio Hour

Making Amends
What makes a true apology? What does it mean to make amends for past mistakes? This hour, TED speakers explore how repairing the wrongs of the past is the first step toward healing for the future. Guests include historian and preservationist Brent Leggs, law professor Martha Minow, librarian Dawn Wacek, and playwright V (formerly Eve Ensler).
Now Playing: Science for the People

#565 The Great Wide Indoors
We're all spending a bit more time indoors this summer than we probably figured. But did you ever stop to think about why the places we live and work as designed the way they are? And how they could be designed better? We're talking with Emily Anthes about her new book "The Great Indoors: The Surprising Science of how Buildings Shape our Behavior, Health and Happiness".
Now Playing: Radiolab

The Third. A TED Talk.
Jad gives a TED talk about his life as a journalist and how Radiolab has evolved over the years. Here's how TED described it:How do you end a story? Host of Radiolab Jad Abumrad tells how his search for an answer led him home to the mountains of Tennessee, where he met an unexpected teacher: Dolly Parton.Jad Nicholas Abumrad is a Lebanese-American radio host, composer and producer. He is the founder of the syndicated public radio program Radiolab, which is broadcast on over 600 radio stations nationwide and is downloaded more than 120 million times a year as a podcast. He also created More Perfect, a podcast that tells the stories behind the Supreme Court's most famous decisions. And most recently, Dolly Parton's America, a nine-episode podcast exploring the life and times of the iconic country music star. Abumrad has received three Peabody Awards and was named a MacArthur Fellow in 2011.