A new breakthrough in thermoelectric materials

April 02, 2015

French physicist Jean Charles Athanase Peltier discovered a key concept necessary for thermoelectric (TE) temperature control in 1834. His findings were so significant, TE devices are now commonly referred to Peltier devices. Since his work, there have been steady advancements in materials and design. Despite the technological sophistication Peltier devices, they are still less energy efficient than traditional compressor/evaporation cooling.

In the 1960's, Peltier devices were primarily made from Bismuth-Telluride (Bi2Te3) or Antimony-Telluride (Sb2Te3) alloys and had a peak efficiency (zT) of 1.1, meaning the electricity going in was only slightly less than the heat coming out. Since the 1960's there have been incremental advancements in alloy technology used in Peltier devices.

In 2014, researchers in South Korea at IBS Center for Integrated Nanostructure Physics along with Samsung Advanced Institute of Technology, the Department of Nano Applied Engineering at Kangwon National University, the Department of Energy Science at Sungkyunkwan University, and Materials Science department at California Institute of Technology California, USA have formulated a new method for creating a novel and much more efficient TE alloy.

TE alloys are special because the metals have an incredibly high melting point. Instead of melting the metals to fuse them, they are combined through a process called sintering which uses heat and/or pressure to join the small, metallic granules. The joint team, including IBS researchers, used a process called liquid-flow assisted sintering which combined all three antimony, bismuth and telluride granules into one alloy (Bi0.5Sb1.5Te3). Additional melted tellurium was used as the liquid between the Bi0.5Sb1.5Te3 granules to help fuse them into a solid alloy, and excess Te is expelled in the process.

By creating the alloy this way, the joints between the fused grains, also known as the grain boundaries, took on a special property. Traditionally sintered Bi0.5Sb1.5Te3 have thick, coarse joints which have led to a decrease in both thermal and electrical conductivity. The new liquid-phase sintering creates grain boundaries which are organized and aligned in seams called dislocation arrays. These dislocation arrays greatly reduce their thermal conduction, leading to an enhancement of their thermoelectric conversion efficiency.

In tests, the efficiency (zT) reached 2.01 at 320 K within the range of 1.86 ±0.15 at 320 K (46.85° C) for 30 samples, nearly doubling the industry standard. When the melt spun Bi0.5Sb1.5Te3 alloy is used in a Peltier cooler, the results are also significant. The new material was able achieve a temperature change of 81 K at 300 K (26.85° C).

The applications for such a material are abundant. As new fabrication techniques are developed, Peltier cooling devices may be used in place of traditional compression refrigeration systems. More importantly, as electrical vehicles and personal electronic devices become more ubiquitous in our daily lives, it is becoming increasingly necessary to have more efficient systems for localized electrical power generation and effective cooling mechanisms. This new thermoelectric alloy paves the way for the future of modern TE devices.
-end-


Institute for Basic Science

Related Thermoelectric Articles from Brightsurf:

Turning heat into power with efficient organic thermoelectric material
Thermoelectric materials can turn a temperature difference into electricity. Organic thermoelectric materials could be used to power wearable electronics or sensors; however, the power output is still very low.

Sprinkled with power: How impurities enhance a thermoelectric material at the atomic level
Magnesium silicide (Mg2Si) is a thermoelectric material that can convert heat into electricity.

Energy-harvesting plastics pass the acid test
Air-stable coatings can improve the longevity of wearable devices that tap into body heat.

Cooling mechanism increases solar energy harvesting for self-powered outdoor sensors
Thermoelectric devices, which use the temperature difference between the top and bottom of the device to generate power, offer some promise for harnessing naturally occurring energy.

Outer tube-selectively boron-doped double-walled carbon nanotubes for thermoelectric applications
A research group led by Hiroyuki Muramatsu of Shinshu University succeeded in selectively doping the outer tube of DWNTs with boron.

Creating stretchable thermoelectric generators
For the first time, a soft and stretchable organic thermoelectric module has been created that can harvest energy from body heat.

How do you power billions of sensors? By converting waste heat into electricity
Osaka University researchers found that thermoelectric power generators lose a great deal of their possible output power because of thermal and electrical contact resistance.

Power dressing
Sensors that are worn on the skin could soon be powered by our own body heat.

Topological semimetals can generate sizable transverse thermoelectric figure of merit
Thermoelectric materials can convert temperature difference in a conducting solid into electrical energy, or vice versa.

Fine-tuning thermoelectric materials for cheaper renewable energy
Researchers from Queen Mary University of London have developed new thermoelectric materials, which could provide a low-cost option for converting heat energy into electricity.

Read More: Thermoelectric News and Thermoelectric Current Events
Brightsurf.com is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon.com.
Can't connect to localhost. Errorcode: 1203