Arrays Of Hundreds Of Identical Millimeter-sized Machines May Replace Conventional Mechanical Devices

April 03, 1997

Some day, aircraft may be powered by an array of hundreds of tiny jet turbines each a fraction of an inch wide, rather than by a single large jet engine.

That idea is among the blue-sky possibilities suggested by a new approach to mechanical design called "massively parallel mechanical systems" being pioneered at Stanford University's Rapid Prototyping Laboratory.

Although replacing a jet engine is well beyond the current state of the art, the scientists propose demonstrating the value of this approach by building several simpler but still useful devices.

One such device is a system to keep aircraft wings from stalling, a condition that causes the wing to lose the upward force that keeps it in the air. Such a system would cover critical parts of a wing with thousands of tiny holes each about 1/25th of an inch in diameter and separated by 2/5th of an inch. In front of each hole is a tiny pressure sensor. When a sensor detects the conditions that precede a stall, it instructs a tiny valve to open, which allows a jet of pressurized air to blow out through the tiny hole behind it. If properly triggered, such jets can prevent a stall from developing.

This kind of system employs mechanical devices that range from a millimeter (1/25th of an inch) to the width of a human hair. Until recently it has not been possible to construct mechanisms in this "mesoscale" size range.

"Right now there is a big gap in the size of the mechanical systems that we can construct," said Friedrich B. "Fritz" Prinz, the Rodney H. Adams Professor of Mechanical Engineering and Materials Science. Normal manufacturing methods create objects a centimeter or larger, and micro-mechanical devices that measure a few microns (about a tenth the width of a human hair) are made using semiconductor manufacturing techniques.

Prinz and his colleagues are developing methods to efficiently make large numbers of mesoscale-sized mechanical devices. They are doing so by combining two different types of techniques. On the one hand, they are miniaturizing traditional manufacturing methods. On the other, they are scaling up techniques used in the semiconductor industry to create millions of transistors on a silicon chip. This allows them to efficiently produce large numbers of mesoscale devices out of metal, ceramics or plastic.

"There are major opportunities in creating new and attractive devices in this intermediate 'mesoscale' size regime," Prinz said. He and Robert Merz, an engineering research associate, described this approach on Wednesday, April 2, at the Seventh International Conference on Rapid Prototyping in San Francisco.

Replacing a few large actuators, turbines, valves and other mechanical devices with large numbers of much smaller devices has a number of potential advantages. For certain applications, key performance parameters, such as power density and response time, improve substantially as the size drops. Large numbers of small, redundant devices also have an inherent edge in reliability when compared to a few large ones.

Prinz, working with Lee Weiss, director of the Shape Deposition Laboratory at Carnegie Mellon University, has developed a layered manufacturing technology, called Shape Deposition Manufacturing (SDM), that makes it possible to create large mechanical arrays in much the same way that computer chips are made.

The ability to make entire devices in place, without any assembly required, is a critical requirement for creating massively parallel mechanical systems. The researchers have fabricated an array of nine nickel wheels, each one a third of a millimeter thick and five millimeters in diameter, mounted on nickel axles to demonstrate that SDM can make entire mechanical devices in place, without any assembly. Similarly, they have made a four-bladed propeller that is five millimeters in diameter: It would take five of these, lined up end to end, to span an inch.

Prinz has proposed to the Defense Advanced Research Project Agency that it support the development of the aircraft flow control system described above and two other projects. If the proposal is approved he will be collaborating with a number of other Stanford researchers, including Merz; Paul Losleben, senior research scientist; Mark A. Cappelli, associate professor of mechanical engineering; John Fessler, acting assistant professor of mechanical engineering; John K. Eaton, professor of mechanical engineering; and Michael Binnard, a graduate student who works with Mark Cutkosky, professor of mechanical engineering. The two additional projects include a satellite thruster system and a tactile interface for virtual reality and teleoperation systems:

As to the idea of a jet aircraft propelled by an array of mesoscale turbines, the massively parallel approach would have some definite theoretical advantages, particularly in power density: It would weigh significantly less than a conventional jet engine of the same power. But an array of tiny turbines would also have some offsetting disadvantages, primarily in increased energy loss caused by siphoning air through hundreds of small holes rather than one large one. "Unfortunately, we don't yet see any clever way to get around these limitations," Prinz said.
-end-


Stanford University

Related Virtual Reality Articles from Brightsurf:

Virtual reality helps measure vulnerability to stress
Behavioral scientists at EPFL have developed a virtual reality test that assesses a person's vulnerability to stress while exploring immersive environments.

Virtual reality forests could help understanding of climate change
The effects of climate change are sometimes difficult to grasp, but now a virtual reality forest, created by geographers, can let people walk through a simulated forest of today and see what various futures may hold for the trees.

New virtual reality software allows scientists to 'walk' inside cells
Virtual reality software which allows researchers to 'walk' inside and analyze individual cells could be used to understand fundamental problems in biology and develop new treatments for disease.

From virtual to reality! Virtual training improves physical and cognitive functions
Researchers at the Smart-Aging Research Center (IDAC) at Tohoku University have developed an innovative training protocol that, utilizing immersive virtual reality (IVR), leads to real physical and cognitive benefits.

Virtual and augmented reality: warnings about the ethical dangers
Research on virtual reality started in the eighties, but it is now that good quality is available to the public and it can become a mass consumer product soon.

Easing the burden of coronavirus with virtual reality
A new article discusses the psychological stresses imposed by the coronavirus pandemic and suggests that virtual reality can help alleviate the psychological impact of the need for social isolation.

Virtual reality makes empathy easier
Virtual reality activates brain networks that increase your ability to identify with other people, according to new research published in eNeuro.

Physiotherapy could be done at home using virtual reality
Virtual reality could help physiotherapy patients complete their exercises at home successfully thanks to researchers at WMG, University of Warwick, who managed to combine VR technology with 3D motion capture.

Using virtual reality to help individuals with autism spectrum disorder
Novel interventions using virtual reality to aid individuals with autism spectrum disorder (ASD) handle common scenarios may include helping youngsters navigate air travel.

Virtual reality illuminates the power of opioid-associated memories
The brain acts differently when remembering environments associated with drug use.

Read More: Virtual Reality News and Virtual Reality Current Events
Brightsurf.com is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon.com.