High color purity 3D printing

May 07, 2020

Selective powder sintering for 3D printing has recently become an increasingly affordable solution for manufacturing made-to-order elements of almost any shape or geometry. This technique involves heating a bed of powder (such as polyamide, PA12) to just below its melting point, using an IR light source to selectively melt a cross section of the powder, then adding more powder and repeating to form a 3D object. To reduce costs and increase printing speed, a photothermal sensitizer is often added to the powders. Typically carbon-based, with a strong broadband absorption, adding these sensitizers to the polymer powders increases the conversion of incident light to heat, which means greater print speeds. However, carbon-based sensitizers can only produce black or gray objects. To create white or colorful prints, visibly transparent equivalents are needed.

A study conducted a few years ago by a team of researchers at ICFO, first authored by Alexander Powell and led by ICREA Professors at ICFO Gerasimos Konstantatos, and Romain Quidant, reported on a solution for overcoming color restrictions in this method using plasmonic nanoparticles. The researchers designed gold nanoparticles coated with silica as a photothermal sensitizer to allow a rapid sintering of polymer powders into 3D objects by having these nanoparticles strongly absorb in the near-infrared, while only minimally interacting with visible light. At resonance, these composites showed greatly improved light-to-heat conversion compared with equivalent composites and could be sintered using low-power light sources. While these particles showed to be very efficient for the rapid fabrication of colored 3D objects, they proved to have certain limitations when trying to print 3D objects in pure white color or multicolor with high color fidelity across a large hue range affecting the quality of the coloration of prints in high concentrations.

Thus, in a recent study published in NanoLetters, the ICFO researchers Alexander Powell, Alexandros Stavrinadis, and Sotirios Christodoulou, led by ICREA Professors at ICFO Gerasimos Konstantatos, and Romain Quidant, have now reported on the use a new sensitizer that has proven to easy overcome these problems.

In their study, the team of researchers has reported on using nanoparticles made of tungsten oxide (WO3) as the photothermal sensitizers for polymer powders. These nanoparticles comprise low cost elements, which make them easy and cheap to fabricate. They are colorless at high concentrations and have a strong absorption in the near infrared region, proving their capability of turning light into heat at a fast rate, and thus enabling them as fast fusing agents. In addition, they can be efficiently turned on or off with electricity or ultraviolet radiation. Even more, they are stable at very high temperatures and demonstrate a heating-to-color change rate superior when compared to other available sensitizers. Finally, when mixed with other color inks, these nanoparticles have been able to reproduce the same shades of color as the original powders, maintaining the color purity of the pristine samples.

The results of the study open a new pathway for the use of plasmonic nanoparticles that can be used to produce high color quality 3D-multicolor objects for advanced manufacturing processes.
-end-
LINKS

Link to the paper: https://pubs.acs.org/doi/10.1021/acs.nanolett.0c00414

Link to the research group led by ICREA Prof. at ICFO Gerasimos Konstantatos: https://www.icfo.eu/lang/research/groups/groups-details?group_id=30

Link to the research group led by ICREA Prof. at ICFO Romain Quidant: https://www.icfo.eu/lang/research/groups/groups-details?group_id=27

ICFO-The Institute of Photonic Sciences

Related Nanoparticles Articles from Brightsurf:

An ionic forcefield for nanoparticles
Nanoparticles are promising drug delivery tools but they struggle to get past the immune system's first line of defense: proteins in the blood serum that tag potential invaders.

Phytoplankton disturbed by nanoparticles
Products derived from nanotechnology are efficient and highly sought-after, yet their effects on the environment are still poorly understood.

How to get more cancer-fighting nanoparticles to where they are needed
University of Toronto Engineering researchers have discovered a dose threshold that greatly increases the delivery of cancer-fighting drugs into a tumour.

Nanoparticles: Acidic alert
Researchers of Ludwig-Maximilians-Universitaet (LMU) in Munich have synthesized nanoparticles that can be induced by a change in pH to release a deadly dose of ionized iron within cells.

3D reconstructions of individual nanoparticles
Want to find out how to design and build materials atom by atom?

Directing nanoparticles straight to tumors
Modern anticancer therapies aim to attack tumor cells while sparing healthy tissue.

Sweet nanoparticles trick kidney
Researchers engineer tiny particles with sugar molecules to prevent side effect in cancer therapy.

A megalibrary of nanoparticles
Using straightforward chemistry and a mix-and-match, modular strategy, researchers have developed a simple approach that could produce over 65,000 different types of complex nanoparticles.

Dialing up the heat on nanoparticles
Rapid progress in the field of metallic nanotechnology is sparking a science revolution that is likely to impact all areas of society, according to professor of physics Ventsislav Valev and his team at the University of Bath in the UK.

Illuminating the world of nanoparticles
Scientists at the Okinawa Institute of Science and Technology Graduate University (OIST) have developed a light-based device that can act as a biosensor, detecting biological substances in materials; for example, harmful pathogens in food samples.

Read More: Nanoparticles News and Nanoparticles Current Events
Brightsurf.com is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon.com.