Now, self-healing materials can mimic human skin, healing again and again

June 11, 2007

CHAMPAIGN, Ill. -- The next generation of self-healing materials, invented by researchers at the University of Illinois, mimics human skin by healing itself time after time. The new materials rely upon embedded, three-dimensional microvascular networks that emulate biological circulatory systems.

"In the same manner that a cut in the skin triggers blood flow to promote healing, a crack in these new materials will trigger the flow of healing agent to repair the damage," said Nancy Sottos, a Willett Professor of materials science and engineering, and the corresponding author of a paper accepted for publication in the journal Nature Materials, and posted on its Web site.

"The vascular nature of this new supply system means minor damage to the same location can be healed repeatedly," said Sottos, who also is a researcher at the university's Beckman Institute.

In the researchers' original approach, self-healing materials consisted of a microencapsulated healing agent and a catalyst distributed throughout a composite matrix. When the material cracked, microcapsules would rupture and release healing agent. The healing agent then reacted with the embedded catalyst to repair the damage.

"With repeated damage in the same location, however, the supply of healing agent would become exhausted," said Scott White, a Willett Professor of aerospace engineering and a researcher at the Beckman Institute. "In our new circulation-based approach, there is a continuous supply of healing agent, so the material could heal itself indefinitely."

To create their self-healing materials, the researchers begin by building a scaffold using a robotic deposition process called direct-write assembly. The process employs a concentrated polymeric ink, dispensed as a continuous filament, to fabricate a three-dimensional structure, layer by layer.

Once the scaffold has been produced, it is surrounded with an epoxy resin. After curing, the resin is heated and the ink - which liquefies - is extracted, leaving behind a substrate with a network of interlocking microchannels.

In the final steps, the researchers deposit a brittle epoxy coating on top of the substrate, and fill the network with a liquid healing agent.

In the researchers' tests, the coating and substrate are bent until a crack forms in the coating. The crack propagates through the coating until it encounters one of the fluid-filled "capillaries" at the interface of the coating and substrate. Healing agent moves from the capillary into the crack, where it interacts with catalyst particles. If the crack reopens under additional stress, the healing cycle is repeated.

"Ultimately, the ability to achieve further healing events is controlled by the availability of active catalyst," said Kathleen S. Toohey, a U. of I. graduate student and lead author of the paper. "While we can pump more healing agent into the network, 'scar tissue' builds up in the coating and prevents the healing agent from reaching the catalyst."

In the current system, the healing process stops after seven healing cycles. This limitation might be overcome by implementing a new microvascular design based on dual networks, the researchers suggest. The improved design would allow new healing chemistries - such as two-part epoxies - to be exploited, which could ultimately lead to unlimited healing capability.

"Currently, the material can heal cracks in the epoxy coating - analogous to small cuts in skin," Sottos said. "The next step is to extend the design to where the network can heal 'lacerations' that extend into the material's substrate."
-end-
With Sottos, Toohey and White, the paper's other co-authors are Jennifer Lewis, the Thurnauer Professor of Materials Science and Engineering and interim director of the Frederick Seitz Materials Research Laboratory, and Jeffrey Moore, a William H. and Janet Lycan Professor of Chemistry and a researcher at the Frederick Seitz Materials Research Laboratory and Beckman Institute. White, Sottos and Moore co-invented self-healing plastic; Lewis and White pioneered direct ink writing of three-dimensional microvascular networks.

The work was funded by the U.S. Air Force Office of Scientific Research and the Beckman Institute.

University of Illinois at Urbana-Champaign

Related Engineering Articles from Brightsurf:

Re-engineering antibodies for COVID-19
Catholic University of America researcher uses 'in silico' analysis to fast-track passive immunity

Next frontier in bacterial engineering
A new technique overcomes a serious hurdle in the field of bacterial design and engineering.

COVID-19 and the role of tissue engineering
Tissue engineering has a unique set of tools and technologies for developing preventive strategies, diagnostics, and treatments that can play an important role during the ongoing COVID-19 pandemic.

Engineering the meniscus
Damage to the meniscus is common, but there remains an unmet need for improved restorative therapies that can overcome poor healing in the avascular regions.

Artificially engineering the intestine
Short bowel syndrome is a debilitating condition with few treatment options, and these treatments have limited efficacy.

Reverse engineering the fireworks of life
An interdisciplinary team of Princeton researchers has successfully reverse engineered the components and sequence of events that lead to microtubule branching.

New method for engineering metabolic pathways
Two approaches provide a faster way to create enzymes and analyze their reactions, leading to the design of more complex molecules.

Engineering for high-speed devices
A research team from the University of Delaware has developed cutting-edge technology for photonics devices that could enable faster communications between phones and computers.

Breakthrough in blood vessel engineering
Growing functional blood vessel networks is no easy task. Previously, other groups have made networks that span millimeters in size.

Next-gen batteries possible with new engineering approach
Dramatically longer-lasting, faster-charging and safer lithium metal batteries may be possible, according to Penn State research, recently published in Nature Energy.

Read More: Engineering News and Engineering Current Events
Brightsurf.com is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon.com.