Research at UC3M improves the bolted joints in airplanes

June 13, 2011

This release is available in Spanish.

The idea for this research arose when the problems of the large structural components of an airplane were being analyzed. These components are made up of a large number of different elements, which are themselves assembled using a variety of techniques, such as soldering, mechanical or adhesive bonding or a combination of these. Of these techniques, mechanical bonding is the method most commonly used in components made of composite materials. For example, the wing of an Airbus 380 alone is composed of over 30,000 elements, with approximately 750,000 bolted joints. These joints are of key importance since they form a weak point that can contribute to the breakage of the element, as well as increase the weight of the aircraft if the design is inefficient, thus raising the aircraft's operating cost.

The researchers have analyzed the performance of these bolted joints in aeronautical structures in which mechanical elements (screws, nuts, washers) are used to join parts that are made of composite materials. Specifically, the scientists at UC3M have analyzed the influence of bolt torque (the force with which the bolt is tightened) and temperature, which varies from -50ºC, when the airplane is flying at an altitude of 10,000 meters, to 90ºC, the temperature to which a bolted joint may be exposed when it is close to a heat source. To do this, they developed a numerical model and analyzed the behavior of these joints under different conditions. "The main conclusion that we drew is that the torque of each joint should be estimated taking into account the range of temperatures to which the plate is going to be subjected, because current industry standards that are applied to determine torque do not take this effect into account", explains one of the authors of the study, Professor Enrique Barbero, head of the Advanced Materials Mechanics research group of the Department of Continuum Mechanics and Structural Analysis at UC3M, which has recently published the study in the Journal of Reinforced Plastics and Composites along with Professors María Henar Miguelez and Carlos Santiuste.

The main type of failure that they found was the crushing of carbon fiber plates against the shaft of the bolt, which is made more likely by low temperatures or by low torque levels. "At -50ºC the volume of the panels is reduced and the effect of the torque is diminished, so the joints that are subjected to these temperatures, such as those that form part of the fuselage and the external structure of the airplane, should have a greater torque so that its effect is maintained even under very low temperatures", affirms Professor Carlos Santiuste. The opposite effect can also be dangerous, the researchers point out, because when temperatures are high or when the torque is too great, the panels made of composite materials may be damaged by being compressed between the head of the bolt and the washer.

This study may have several applications. Optimizing the design of bolted joints in aeronautical structures would allow safety coefficients in the design to be reduced, which would result in a lower structural weight. This reduction would then lead to lower fuel consumption and, therefore, a reduction in the aircraft's operating costs and its impact on the environment. Along these lines, the development of more energy efficient airplanes with a lower environmental impact falls within the "Clean Sky" initiative that is part of the Seventh Framework Programme of the European Union.

This research has been approached with a global view, taking in everything from the design phase through the operation of the structural elements, giving it a markedly interdisciplinary character. In order to do this, collaboration between two research groups from different departments of the UC3M was established. These are: the Department of Advanced Materials Mechanics, coordinated by Professor Enrique Barbero, which focuses on the study of lightweight structural elements; and the Mechanical and Biomechanical Component Manufacturing and Design Technology section of the Mechanical Englineering Department, lead by Professor Mª Henar Miguelez, which works on the study of mechanized processes. In this way, the researchers were able to analyze the problems in these joints, which combine a temperature problem and a mechanical one, due to the effects of temperature and torque. "This kind of collaboration between research groups is very interesting, as the majority of the most relevant lines of research are interdisciplinary in nature, and it allows us to take on more ambitious lines of research", comments Professor Barbero. As a result of the experience gained through this project, a proposal submitted to the National R + D + i Plan has been accepted and will receive enough funding to continue this line of research for the next three years, and to carry out a series of experimental tests.
-end-


Carlos III University of Madrid

Related Composite Materials Articles from Brightsurf:

New composite material revs up pursuit of advanced electric vehicles
Scientists at Oak Ridge National Laboratory used new techniques to create a composite that increases the electrical current capacity of copper wires, providing a new material that can be scaled for use in ultra-efficient, power-dense electric vehicle traction motors.

Analyzing pros and cons of two composite manufacturing methods
Airplane wings and wind turbine blades are typically created using bulk polymerization in composite manufacturing facilities.

Visualization of functional components to characterize optimal composite electrodes
Researchers have developed a visualization method that will determine the distribution of components in battery electrodes using atomic force microscopy.

Study suggests polymer composite could serve as lighter, non-toxic radiation shielding
A new study suggests that a polymer compound embedded with bismuth trioxide particles holds tremendous potential for replacing conventional radiation shielding materials, such as lead.

Scientists develop stable luminescent composite material based on perovskite nanocrystals
An international team of scientists that includes researchers from ITMO University has developed a new composite material based on perovskite nanocrystals for the purpose of creating miniature light sources with improved output capacity.

Composite metal foams take the heat, move closer to widespread applications
Engineering researchers have demonstrated that composite metal foams (CMFs) can pass so-called 'simulated pool fire testing' with flying colors, moving the material closer to use in applications such as packaging and transportation of hazardous materials.

Using holograms helps in studying the quality of composite materials
Composite materials have a complicated structure and specified mechanical or physical properties.

Scientists develop a composite membrane for long-life zinc-based flow batteries
Researchers led by Profs. LI Xianfeng from the Dalian Institute of Chemical Physics (DICP) of the Chinese Academy of Sciences recently developed a composite membraneĀ for long-life zinc-based flow batteries.

An early warning system for damage in composite materials
A team at the National Institute of Standards and Technology (NIST) has developed a tool to monitor changes in widely used composite materials known as fiber reinforced polymers (FRPs), which can be found in everything from aerospace and infrastructure to wind turbines.

Novel composite antimicrobial film could take a bite out of foodborne illnesses
A novel composite film -- created by the bonding of an antimicrobial layer to conventional, clear polyethylene plastic typically used to vacuum-package foods such as meat and fish -- could help to decrease foodborne illness outbreaks, according to researchers in Penn State's College of Agricultural Sciences.

Read More: Composite Materials News and Composite Materials Current Events
Brightsurf.com is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon.com.