First step towards a better prosthetic leg? Trip people over and over

June 19, 2019

Andrés Martínez strode briskly on the treadmill, staring straight ahead and counting backwards by seven from 898, a trick to keep his brain from anticipating the literal stumbling block heading his way: a compact 35 pounds of steel specifically designed to make him fall.

Special goggles kept him from looking down. Arrows on an eye-level screen kept him from walking off the sides. A harness attached to a ceiling beam kept him safe. Sure enough, when a computer program released the steel block, it glided onto the treadmill, and the Vanderbilt University PhD student struggled to stay on his feet.

That automatic stumble response, so natural for most people, is virtually impossible for those who use prosthetic legs, simply because even state-of-the-art prosthetics cannot adapt to stumbling. Patients with above-the-knee amputations are far more likely to fall than typical counterparts in their age group.

The first step a Vanderbilt team took in addressing that challenge in lower-body prosthetics was coming to understand the way people with two legs catch themselves, accomplished by covering test subjects with motion-capturing sensors. It also required tripping them over and over - 190 times, to be exact -- for a study published this month in the Journal of NeuroEngineering and Rehabilitation. But because humans are so mentally geared to resist stumbling, a team of Vanderbilt mechanical engineers first had to design the stumbling device described above.

"Not only did our treadmill device have to trip them, it had to trip them at specific points in their gait," said Shane King, a PhD student and lead author on the paper. "People stumble differently depending on when their foot hits a barrier. The device also had to overcome their fear of falling, so they couldn't see or feel when the block was coming."

In addition to protecting test subjects, the harness included a scale. If a subject put 50 percent or more of their weight on it, that counted as a fall. The team's design for the machine and outcomes of their tests are available for other labs to use in the open-source journal.

Michael Goldfarb, H. Fort Flowers Professor of Mechanical Engineering and the principal investigator on the study, said designing the stumble device and measuring outcomes was only the first of three parts.

"So now we understand what the stumble reflex should look like," he said. "The next phase is to take that information and program it into computer-controlled prosthetic legs. After that, we will safely stumble amputees wearing both commercially available prosthetics and the ones we've designed with these reflexes and learn whether ours can prevent more falls."
-end-
The work was performed through the Center for Rehabilitation Engineering and Assistive Technology at Vanderbilt University. Other team members were Karl Zelik, assistant professor of mechanical engineering, and Maura Eveld, a PhD student in mechanical engineering.

Vanderbilt University

Related Mechanical Engineering Articles from Brightsurf:

Best practices for mechanical ventilation in patients with ARDS, COVID-19
A team from pulmonary and critical care medicine at Michigan Medicine outlines 20 evidence-based practices shown to reduce time spent on a ventilator and death in patients with acute respiratory failure and acute respiratory distress -- conditions that have many overlaps with severe COVID-19.

How cells use mechanical tension sensors to interact with their environment
In a painstaking experiment, scientists suspended a single protein filament between two microscopic beads.

Mechanical forces of biofilms could play role in infections
Studying bacterial biofilms, EPFL scientists have discovered that mechanical forces within them are sufficient to deform the soft material they grow on, e.g. biological tissues, suggesting a ''mechanical'' mode of bacterial infection.

How mechanical forces nudge tumors toward malignancy
Researchers studying two forms of skin cancer identified a long-overlooked factor determining why some tumors are more likely to metastasize than others: the physical properties of the tissue in which the cancer originates.

Building mechanical memory boards using origami
Origami can be used to create mechanical, binary switches, and in Applied Physics Letters, researchers report the fabrication of such a paper device, using the Kresling pattern, that can act as a mechanical switch.

Not just light: The sensitivity of photoreceptors to mechanical stimuli is unveiled
''We thought we knew almost everything about photoreceptors, but we have proved that is not the case''.

A mechanical way to stimulate neurons
Magnetic nanodiscs can be activated by an external magnetic field, providing a research tool for studying neural responses.

Cell removal as the result of a mechanical instability
Researchers at Kanazawa University report in the Biophysical Journal that the process of cell removal from an epithelial layer follows from an inherent mechanical instability.

Researchers demonstrate transport of mechanical energy, even through damaged pathways
Researchers from the University of Illinois at Urbana-Champaign's Grainger College of Engineering have experimentally demonstrated a new way to transport energy even through wave-guides that are defective, and even if the disorder is a transient phenomenon in time.

Tissues protect their DNA under mechanical stress
Nuclei and genetic material deform.

Read More: Mechanical Engineering News and Mechanical Engineering Current Events
Brightsurf.com is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon.com.