Low power, highly reliable, wireless, infrared local area networks demonstrated

July 24, 2001

University Park, Pa. --- Penn State engineers have shown that broadband, wireless, indoor, local area communication networks that rely on non-line-of-sight infrared (IR) signal transmission can offer low error rates as well as safe, low - below one Watt - power levels. Dr. Mohsen Kavehrad, professor of electrical engineering and holder of the W. L. Weiss (AMERITECH) chair, says, "Line-of-sight or point-to-point infrared signal transmission, which is used, for example, in television remote controls, is highly efficient at low power levels but suffers from the need for alignment between the transmitter and receiver. If someone 'shadows' or blocks the remote control beam while you're trying to change the channel, the signal can't get through.

"On the other hand, non-line-of-sight transmission, which uses a broad diffuse beam, suffers less from shadowing but usually forfeits the power efficiency, broadband and low error rate values that infrared transmission can offer." Now, however, Kavehrad and his colleagues at Penn State's Center for Information and Communications Technology Research have developed a new link design that uses a multi-beam transmitter with a narrow field of view receiver. The system has a bit-error rate of only one error per billion bits and uses milliwatt transmitted power levels. Kavehrad says, "This error rate is unmatched considering the offered transmission capacity." The Penn State researcher detailed the system Sunday, July 22, at the Fifth World Multi-Conference on Systemics, Cybernetics and Informatics SCI 2001 meeting in Orlando, Florida. His paper, "Some Recent Advances in Indoor Broadband Infrared Wireless Communications," is co-authored by Dr. Svetla Jivkova, research associate. To use the Penn State signaling scheme, for example, to form a local area network for a group of computers in a room, each machine is equipped with a low power infrared source and a holographic beam splitter. The original low power beam is separated into several narrow beams, which strike the ceiling and walls at points that form an invisible grid throughout the entire volume of the room. Because the beams are also reflected at each of the strike points, they can be used to send or receive information. Since the beams created by the splitter are narrow, narrow field-of-view receivers are used. Using a narrow field of view receiver makes it easier to filter out noise. In addition, receivers consisting of more than one element can insure continued coverage when some of the transmitter beams are blocked. Kavehrad notes, "Others have attempted to develop local area networks with radio frequencies. However, indoors, radio frequencies can pose a radiation hazard."

"Infrared signals, on the other hand, pose no such hazard, especially at the low powers used by our system. However, since the sun is an infrared emitter, as well as fluorescent and incandescent bulbs, light coming in through windows or from artificial lighting can add background noise to the system. This noise, to some extent, can be filtered at the receivers." The Penn State team developed a framework for computer simulation under which properties of room, transmitter and receiver are quantified. Using the simulation results, they showed that the system has a bit-error rate of only one error per billion bits in 99 percent of the coverage area at bit rates up to a few hundred megabits per second. In addition, the system uses transmitted power levels well below one Watt.
-end-
The wireless infrared communication system is being patented by the University. The research was supported by grants from the National Science Foundation and the Pennsylvania technology development program known as the Pittsburgh Digital Greenhouse.

EDITORS: Dr. Kavehrad is at 814-865-7179 or mkavehrad@psu.edu by email.

Penn State

Related Wireless Articles from Brightsurf:

5G wireless may lead to inaccurate weather forecasts
Upcoming 5G wireless networks that will provide faster cell phone service may lead to inaccurate weather forecasts, according to a Rutgers study on a controversial issue that has created anxiety among meteorologists.

Terahertz receiver for 6G wireless communications
Future wireless networks of the 6th generation (6G) will consist of a multitude of small radio cells that need to be connected by broadband communication links.

Faster LEDs for wireless communications from invisible light
Researchers have solved a major problem for optical wireless communications - the process by which light carries information between cell phones and other devices.

A location system to drive future wireless innovation
There are many barriers to innovation in wireless communications. Inadequate documentation; uncooperative chipset manufacturers; widely varying hardware and software specifications; steep learning curves in the experimentation phase and difficulties in prototyping are among the biggest issues that hamper development.

Novel transmitter protects wireless devices from hackers
MIT researchers have developed a novel transmitter that frequency hops each individual 1 or 0 bit of a data packet, every microsecond, which is fast enough to thwart even the quickest hackers.

New algorithm keeps data fresh in wireless networks
Algorithm provides networks with the most current information available while avoiding data congestion.

Want to make your factory wireless? NIST can guide you!
Knowing that it will take reliable wireless communications to make the smart factory of the not-so-distant future a reality, the National Institute of Standards and Technology (NIST) has published the first-ever set of science-based guidelines to help users select the best wireless system for any specific industrial environment, custom-design the setup to make it work, successfully deploy it, and then ensure that the network performs as needed.

The first wireless flying robotic insect takes off
Engineers at the University of Washington have created RoboFly, the first wireless flying robotic insect.

The future of wireless communications is terahertz
Electrical and optical engineers in Australia have designed a novel platform that could tailor telecommunication and optical transmissions.

Advances open new frequency range for wireless communications
The 'internet of things,' which make everything from your toaster to your front door accessible online, has driven an explosion in data traffic and taken up huge amounts of bandwidth.

Read More: Wireless News and Wireless Current Events
Brightsurf.com is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon.com.