Patented technique makes for toughter heat-resistant plastics

September 09, 2000

COLUMBUS, Ohio - Tough, heat-resistant plastics may soon find their way into car and airplane engines as a result of research at Ohio State University.

Scientists here have patented a method of mixing plastic with silica to create a material three to four times tougher than the plastic alone.

Plastic engine parts would mean lighter, more fuel-efficient cars and airplanes, but today's heat-resistant plastics aren't tough enough -- they shatter at the smallest impact, said John Lannutti, associate professor of materials science and engineering at Ohio State.

The new composite material is tougher than plastic alone because it divides the force of an impact into many small interactions involving millions of individual silica particles.

"We think that as a crack starts traveling through the composite, it breaks up into finer and finer cracks, until the material has dissipated the energy of the impact," Lannutti said.

Lannutti developed the method of producing these materials with Robert Seghi, associate professor of restorative and prosthetic dentistry at Ohio State, and graduate student Jiazhong Luo. Their goal, at first, was to create tough plastic dental fillings.

After moderate success -- they created a plastic that was about as good as today's standard fillings -- Lannutti tried the technique with a different kind of plastic for Ohio Aerospace Institute member BFGoodrich Co.

BFGoodrich supplied plastic powder for Lannutti's experiments, and will manufacture parts containing this silica for further testing.

Lannutti and his colleagues call the method "synergistic toughening," or "toughening across scales," because it strengthens material down to the scale of the individual particles.

The silica particles they use are only 50 nanometers wide -- about 100 times smaller than the width of a human hair -- and each particle contains a host of even smaller pores that measure only a couple of nanometers across.

What makes the patented manufacturing method unique is that the researchers force melted plastic to fill these tiny pores, creating a strong bond between atoms of silica and plastic over a large surface area.

"So basically we can create toughness that starts at the nanoscale," said Lannutti.

Eventually consumers may one day find more plastic parts under their car hoods, or on a commercial airplane wing -- places where iron, steel, and aluminum are used today, Lannutti said. Sooner than that, though, military aircraft will probably take advantage of the technology.

It was military testing of parts made with heat-resistant plastic and reinforced with graphite fiber that uncovered the need for tougher plastics.

Impacts such as a bird flying into an airplane wing, or even a wrench falling onto a part, would shatter the plastic and leave behind only the woven graphite fibers, Lannutti said.

Still, the brittle plastic's tolerance of temperatures up to 800šF makes it ideal for parts surrounding hot jet engines.

In laboratory tests, the plastic-silica composite material retained the heat-resistance of fiber-reinforced plastics, but improved resistance to impacts by four to five times.

Lannutti said the new composite isn't as hard as steel, but displays good heat resistance at a fraction of the weight of steel.
-end-
Contact: John Lannutti, 614-292-3926, Lannutti.1@osu.edu
Written by Pam Frost, 614-292-9475, Frost.18@osu.edu

Ohio State University

Related Plastic Articles from Brightsurf:

Is zoom increasing the demand for plastic surgery
Patients are seeking plastic surgery in record numbers, citing their appearance on Zoom as a cause.

Closing the plastic loop
Researchers develop a one-pot, low temperature catalytic method to turn polyethylene polymers into alkylaromatic molecules.

Does science have a plastic problem? Microbiologists take steps to reducing plastic waste
A research group based at the University of Edinburgh's Roslin Institute, developed an approach to reduce plastic waste produced by their lab.

Plastic-eating enzyme 'cocktail' heralds new hope for plastic waste
The UK-US team who re-engineered the plastic-eating enzyme PETase have now created an enzyme 'cocktail' which can digest plastic up to six times faster.

Scientists sound alarm on plastic pollution
A new study shows that despite global commitments to address plastic pollution, growth in plastic waste, or 'plastics emissions' continues to outpace reduction.

Ecologists sound alarm on plastic pollution
Research led by ecologists at the University of Toronto examining plastic pollution entering oceans, rivers and lakes around the world annually, outlines potential impacts of various mitigation strategies over the coming decade.

The persistence of plastic
The amount of synthetic microfiber we shed into our waterways has been of great concern over the last few years, and for good reason: Every laundry cycle releases in its wastewater tens of thousands of tiny, near-invisible plastic fibers whose persistence and accumulation can affect aquatic habitats and food systems, and ultimately our own bodies in ways we have yet to discover.

There is at least 10 times more plastic in the Atlantic than previously thought
Scientists measured 12-21 million tonnes of three of the most common types of plastic in the top 200 metres of the Atlantic.

Seafood study finds plastic in all samples
A study of five different seafoods has found traces of plastic in every sample tested.

A world drowning in plastic pollution
Almost one billion tonnes of plastic will be dumped on land and in the oceans over the period from 2016 to 2040 unless the world acts, say a team of 17 global experts who have developed a computer model to track the stocks and flows of plastic around the world.

Read More: Plastic News and Plastic Current Events
Brightsurf.com is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon.com.