Theoretically, two layers are better than one for solar-cell efficiency

September 15, 2020

Solar cells have come a long way, but inexpensive, thin film solar cells are still far behind more expensive, crystalline solar cells in efficiency. Now, a team of researchers suggests that using two thin films of different materials may be the way to go to create affordable, thin film cells with about 34% efficiency.

"Ten years ago I knew very little about solar cells, but it became clear to me they were very important," said Akhlesh Lakhtakia, Evan Pugh University Professor and Charles Godfrey Binder Professor of Engineering Science and Mechanics, Penn State.

Investigating the field, he found that researchers approached solar cells from two sides, the optical side -- looking on how the sun's light is collected -- and the electrical side -- looking at how the collected sunlight is converted into electricity. Optical researchers strive to optimize light capture, while electrical researchers strive to optimize conversion to electricity, both sides simplifying the other.

"I decided to create a model in which both electrical and optical aspects will be treated equally," said Lakhtakia. "We needed to increase actual efficiency, because if the efficiency of a cell is less than 30% it isn't going to make a difference." The researchers report their results in a recent issue of Applied Physics Letters.

Lakhtakia is a theoretician. He does not make thin films in a laboratory, but creates mathematical models to test the possibilities of configurations and materials so that others can test the results. The problem, he said, was that the mathematical structure of optimizing the optical and the electrical are very different.

Solar cells appear to be simple devices, he explained. A clear top layer allows sunlight to fall on an energy conversion layer. The material chosen to convert the energy, absorbs the light and produces streams of negatively charged electrons and positively charged holes moving in opposite directions. The differently charged particles get transferred to a top contact layer and a bottom contact layer that channel the electricity out of the cell for use. The amount of energy a cell can produce depends on the amount of sunlight collected and the ability of the conversion layer. Different materials react to and convert different wavelengths of light.

"I realized that to increase efficiency we had to absorb more light," said Lakhtakia. "To do that we had to make the absorbent layer nonhomogeneous in a special way."

That special way was to use two different absorbent materials in two different thin films. The researchers chose commercially available CIGS -- copper indium gallium diselenide -- and CZTSSe -- copper zinc tin sulfur selenide-- for the layers. By itself, CIGS's efficiency is about 20% and CZTSSe's is about 11%.

These two materials work in a solar cell because the structure of both materials is the same. They have roughly the same lattice structure, so they can be grown one on top of the other, and they absorb different frequencies of the spectrum so they should increase efficiency, according to Lakhtakia.

"It was amazing," said Lakhtakia. "Together they produced a solar cell with 34% efficiency. This creates a new solar cell architecture -- layer upon layer. Others who can actually make solar cells can find other formulations of layers and perhaps do better."

According to the researchers, the next step is to create these experimentally and see what the options are to get the final, best answers.
-end-
The first author of the paper is Faiz Ahmad, doctoral student in engineering science and mechanics, Penn State. Peter B. Monk, Unidel Professor of Mathematical Sciences, University of Delaware, filled out the research team.

The National Science Foundation supported this research.

Penn State

Related Solar Cells Articles from Brightsurf:

Solar cells of the future
Organic solar cells are cheaper to produce and more flexible than their counterparts made of crystalline silicon, but do not offer the same level of efficiency or stability.

A blast of gas for better solar cells
Treating silicon with carbon dioxide gas in plasma processing brings simplicity and control to a key step for making solar cells.

Record efficiency for printed solar cells
A new study reports the highest efficiency ever recorded for full roll-to-roll printed perovskite solar cells.

Next gen solar cells perform better when there's a camera around
A literal ''trick of the light'' can detect imperfections in next-gen solar cells, boosting their efficiency to match that of existing silicon-based versions, researchers have found.

On the trail of organic solar cells' efficiency
Scientists at TU Dresden and Hasselt University in Belgium investigated the physical causes that limit the efficiency of novel solar cells based on organic molecular materials.

Exciting tweaks for organic solar cells
A molecular tweak has improved organic solar cell performance, bringing us closer to cheaper, efficient, and more easily manufactured photovoltaics.

For cheaper solar cells, thinner really is better
Researchers at MIT and at the National Renewable Energy Laboratory (NREL) have outlined a pathway to slashing costs further, this time by slimming down the silicon cells themselves.

Flexible thinking on silicon solar cells
Combining silicon with a highly elastic polymer backing produces solar cells that have record-breaking stretchability and high efficiency.

Perovskite solar cells get an upgrade
Rice University materials scientists find inorganic compounds quench defects in perovskite-based solar cells and expand their tolerance of light, humidity and heat.

Can solar technology kill cancer cells?
Michigan State University scientists have revealed a new way to detect and attack cancer cells using technology traditionally reserved for solar power.

Read More: Solar Cells News and Solar Cells Current Events
Brightsurf.com is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon.com.