Efficient low-cost method for hydrogenation of graphene with visible light

October 06, 2016

An environmentally friendly, efficient and low-cost method for hydrogenation of graphene with visible light has been developed by researchers at Uppsala University and AstraZeneca Gothenburg, Sweden. The research study is presented in an article in Nature Communications.

The study shows that the two-dimensional and atom-thin carbon material graphene reacts with formic acid in a water solution upon irradiation with visible light. In the reaction, formic acid acts as masked hydrogen and a material is produced where hydrogen extensively has been added to graphene. One says that graphene has been hydrogenated.

The study was performed by Assoc. Prof. Henrik Ottosson's research group at the Department of Chemistry - Ångström Laboratory, together with colleagues in Chemistry, Physics and Engineering at Uppsala University and at AstraZeneca Gothenburg.

" The reaction is convenient and cheap, and hydrogenated graphene may be applied within areas such as hydrogen storage. Additionally, upon functionalization of graphene one can open a band gap and this fact is of high relevance for electronics applications", says Henrik Ottosson.

Yet, graphene research is a side-project in Henrik Ottosson's group. The group normally studies the behaviours of various aromatic hydrocarbons upon irradiation, and they apply a rule, the so-called Baird's rule, which can be derived through chemically applied quantum mechanics.

Chemical compounds that are aromatic have an inherently high stability and often they are not easy to degrade. Benzene is the most well known aromatic compound and more than half of all known chemical compounds contain aromatic groups.

The high stability of aromatic compounds is explained by Hückel´s "4n+2" rule, but this rule is only valid for compounds in their electronic ground states. Upon exposure to light of a certain wavelength, the aromatic compounds reach electronically excited states.

According to Baird, compounds that are aromatic in the ground state become antiaromatic and reactive in the excited state. The rule, neglected for decades, can now be used to describe various behaviours of aromatic compounds when irradiated.

Using Baird's rule, Henrik Ottosson's group develops new light-initiated reactions. First, they studied addition of hydrosilanes to benzenes, naphthalene and gradually larger polycyclic aromatic hydrocarbons (hydrosilanes are compounds that can be regarded as heavy analogues of hydrogen).

Despite the fact that it is not possible to explain if, and how, Baird's rule can be applied to graphene (an essentially infinitely large polycyclic aromatic hydrocarbon), the group explored graphene chemistry and found a very efficient addition reaction when using formic acid.

At AstraZeneca one sees interesting possibilities for the future:

"It has become more common to apply light-initiated reactions during the development of new molecules in our drug research programs. We challenge ourselves to continuously develop more efficient and environmentally friendly chemical methods. The recent progress we have seen in photochemistry, highlighted by the results herein, will increase our opportunities to access chemistry that no one thought possible a few years ago. In addition, graphene based materials have exceptional inherent properties. There is a wealth of possible applications that could result in the next biomedical revolution" , says Joakim Bergman, Innovative Medicines and Early Development Biotech Unit AstraZeneca Gothenburg.
Papadakis, R. et al; Metal-Free Photochemical Silylations and Transfer Hydrogenations of Benzenoid Hydrocarbons and Graphene; Nature Communications (2016) DOI 10.1038/NCOMMS12962

Kontakt: Docent Henrik Ottosson, Institutionen för kemi - Ångström, Uppsala universitet, henrik.ottosson@kemi.uu.se

Uppsala University

Related Graphene Articles from Brightsurf:

How to stack graphene up to four layers
IBS research team reports a novel method to grow multi-layered, single-crystalline graphene with a selected stacking order in a wafer scale.

Graphene-Adsorbate van der Waals bonding memory inspires 'smart' graphene sensors
Electric field modulation of the graphene-adsorbate interaction induces unique van der Waals (vdW) bonding which were previously assumed to be randomized by thermal energy after the electric field is turned off.

Graphene: It is all about the toppings
The way graphene interacts with other materials depends on how these materials are brought into contact with the graphene.

Discovery of graphene switch
Researchers at Japan Advanced Institute of Science and Technology (JAIST) successfully developed the special in-situ transmission electron microscope technique to measure the current-voltage curve of graphene nanoribbon (GNR) with observing the edge structure and found that the electrical conductance of narrow GNRs with a zigzag edge structure abruptly increased above the critical bias voltage, indicating that which they are expected to be applied to switching devices, which are the smallest in the world.

New 'brick' for nanotechnology: Graphene Nanomesh
Researchers at Japan advanced institute of science and technology (JAIST) successfully fabricated suspended graphene nanomesh (GNM) by using the focused helium ion beam technology.

Flatter graphene, faster electrons
Scientists from the Swiss Nanoscience Institute and the Department of Physics at the University of Basel developed a technique to flatten corrugations in graphene layers.

Graphene Flagship publishes handbook of graphene manufacturing
The EU-funded research project Graphene Flagship has published a comprehensive guide explaining how to produce and process graphene and related materials (GRMs).

How to induce magnetism in graphene
Graphene, a two-dimensional structure made of carbon, is a material with excellent mechani-cal, electronic and optical properties.

Graphene: The more you bend it, the softer it gets
New research by engineers at the University of Illinois combines atomic-scale experimentation with computer modeling to determine how much energy it takes to bend multilayer graphene -- a question that has eluded scientists since graphene was first isolated.

How do you know it's perfect graphene?
Scientists at the US Department of Energy's Ames Laboratory have discovered an indicator that reliably demonstrates a sample's high quality, and it was one that was hiding in plain sight for decades.

Read More: Graphene News and Graphene Current Events
Brightsurf.com is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon.com.