Energy-harvesting plastics pass the acid test

October 06, 2020

A polymer previously used to protect solar cells may find new applications in consumer electronics, reveals a KAUST team studying thin films capable of converting thermal energy into electricity.

When two sides of a semiconductor are at different temperatures, electron migration from hot to cool areas can generate a current. This phenomenon, known as the thermoelectric effect, typically requires semiconductors with rigid ceramic structures to maintain the heat difference between the two sides. But the recent discovery that polymers also exhibit thermoelectric behavior has prompted a rethink of how to exploit this method for improved energy harvesting, including incorporation into wearable devices.

Derya Baran and her team at KAUST are helping to engineer self-powered devices using a conducting polymer containing a blend of poly(3,4-ethylenedioxythiophene) and polystyrenesulfonate (PEDOT:PSS) chains. Relatively inexpensive and easy to process for applications, including inkjet printing, PEDOT:PSS is one of the top-performing thermoelectric polymers thanks to its ability to take in efficiency-boosting additives known as dopants.

Diego Rosas-Villalva, a researcher in Baran's group, explains that thermoelectric PEDOT:PSS thin films are often exposed to dopants in the form of strong acids. This process washes away loose PSS chains to improve polymer crystallinity and leaves behind particles that oxidize PEDOT chains to boost electrical conductivity.

"We use nitric acid because it's one of the best dopants for PEDOT," says Rosas-Villalva. "However, it evaporates rather easily, and this decreases the performance of the thermoelectric over time."

After the doping step is completed, the PEDOT:PSS film has to undergo a reverse procedure to neutralize or "dedope" some conductive particles to improve thermoelectric power generation.

Typical dedopants include short hydrocarbons containing positively charged amine groups. The KAUST researchers were studying a polymerized version of these amine chains, known as ethoxylated polyethylenimine, when they noticed a remarkable effect--PEDOT:PSS films dedoped with polyethylenimine retained twice as much thermoelectric power after one week compared with untreated specimens.

The team's investigations revealed that polyethylenimine was effective at encapsulating PEDOT:PSS films to prevent nitric acid escape. In addition, this coating modified the electronic properties of the thermoelectric polymer to make it easier to harvest energy from sources, including body heat.

"We were not expecting that this polymer would improve the lifetime of the device, especially because it's such a thin film--less than 5 nanometers," says Villalva. "It's been incorporated into other organic electronics before, but barely explored for thermoelectrics."
-end-


King Abdullah University of Science & Technology (KAUST)

Related Thermoelectric Articles from Brightsurf:

Turning heat into power with efficient organic thermoelectric material
Thermoelectric materials can turn a temperature difference into electricity. Organic thermoelectric materials could be used to power wearable electronics or sensors; however, the power output is still very low.

Sprinkled with power: How impurities enhance a thermoelectric material at the atomic level
Magnesium silicide (Mg2Si) is a thermoelectric material that can convert heat into electricity.

Energy-harvesting plastics pass the acid test
Air-stable coatings can improve the longevity of wearable devices that tap into body heat.

Cooling mechanism increases solar energy harvesting for self-powered outdoor sensors
Thermoelectric devices, which use the temperature difference between the top and bottom of the device to generate power, offer some promise for harnessing naturally occurring energy.

Outer tube-selectively boron-doped double-walled carbon nanotubes for thermoelectric applications
A research group led by Hiroyuki Muramatsu of Shinshu University succeeded in selectively doping the outer tube of DWNTs with boron.

Creating stretchable thermoelectric generators
For the first time, a soft and stretchable organic thermoelectric module has been created that can harvest energy from body heat.

How do you power billions of sensors? By converting waste heat into electricity
Osaka University researchers found that thermoelectric power generators lose a great deal of their possible output power because of thermal and electrical contact resistance.

Power dressing
Sensors that are worn on the skin could soon be powered by our own body heat.

Topological semimetals can generate sizable transverse thermoelectric figure of merit
Thermoelectric materials can convert temperature difference in a conducting solid into electrical energy, or vice versa.

Fine-tuning thermoelectric materials for cheaper renewable energy
Researchers from Queen Mary University of London have developed new thermoelectric materials, which could provide a low-cost option for converting heat energy into electricity.

Read More: Thermoelectric News and Thermoelectric Current Events
Brightsurf.com is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon.com.