Radically simple technique developed to grow conducting polymer thin films

November 01, 2010

Oil and water don't mix, but add in some nanofibers and all bets are off.

A team of UCLA chemists and engineers has developed a new method for coating large surfaces with nanofiber thin films that are both transparent and electrically conductive. Their method involves the vigorous agitation of water, dense oil and polymer nanofibers. After this solution is sufficiently agitated it spreads over virtually any surface, creating a film.

"The beauty of this method lies in its simplicity and versatility," said California NanoSystems Institute (CNSI) researcher Richard B. Kaner, a professor of chemistry and biochemistry and a professor of materials science and engineering at the UCLA Henry Samueli School of Engineering and Applied Science. "The materials used are inexpensive and recyclable, the process works on virtually any substrate, it produces a uniform thin film which grows in seconds and the entire thing can be done at room temperature."

Conducting polymers combine the flexibility and toughness of plastics with electrical properties. They have been proposed for applications ranging from printed electronic circuits to supercapacitors but have failed to gain widespread use because of difficulties processing them into films.

"Conducting polymers have enormous potential in electronics, and because this technique works with so many substrates, it can be used in a broad spectrum of applications, including organic solar cells, light-emitting diodes, smart glass and sensors," said Yang Yang, a professor of materials science and engineering at the Samueli School of Engineering and Applied Science and faculty director of the Nano Renewable Energy Center at the CNSI.

One of the potential applications is smart, or switchable, glass that can change between states when an electric current is applied -- for example, switching between see-through and opaque states to let light in or block it. The UCLA research group is applying the technique to other nanomaterials in addition to polymer nanofibers in the hopes of expanding the number of available applications.

The team's solution-based technique, published in the peer-reviewed journal Proceedings of National Academy of Sciences, was discovered serendipitously when a transparent film of polymer spread up the walls of a container while nanofibers in water were being purified with chloroform.

"What drew me in immediately was the eerie phenomenon of what appeared to be self-propelled fluid flow," said Julio M. D'Arcy, lead author on the PNAS paper and a senior graduate student in the Kaner's UCLA lab.

"Now I can tell people that I make films in L.A.," he joked.

When water and oil are mixed, a blend of droplets is formed, creating a water-oil interface that serves as an entry point for trapping polymer nanofibers at liquid-liquid interfaces. As droplets unite, a change in the concentration of blended solids at the water-oil interface leads to a difference in surface tension. Spreading up a glass wall occurs as result of an attempt to reduce the surface-tension difference. Directional fluid flow leads to a continuously conductive thin film comprised of a single monolayer of polymer nanofibers. The uniformity of the film surface is due to the particles being drawn out of the water-oil interface, sandwiched between two fluids of opposing surface tensions.

Development of the technology is occurring in collaboration with Fibron Technologies Inc., with support from the National Science Foundation through a Small Business Technology Transfer grant. Fibron is a small company that has licensed the technology from UCLA. It was founded by Kaner, who serves as chief scientific adviser, and two of his former Ph.D. students -- Christina Baker and Henry Tran, who have gone on to take leadership roles in the company.

Fibron's CEO, Christian Behrenbruch, said "working with UCLA to develop this technology has been a win-win. It enables us to access incredibly innovative people, but also, the NSF has helped enable the establishment of a formal and transparent IP releationship with the university. The good news is that this technology is moving rapidly into commercial development."

Other techniques exist for creating thin films of conducting polymers, but each technique tends to work only a limited number of applications, or they are not feasible for scaling up. A method has long been sought which would overcome the limitations of each of the previous methods. The water and oil technique, with a bit of nanotechnology thrown in, might provide just that -- a scalable universal method for creating large thin films of conducting polymers.
-end-
The California NanoSystems Institute at UCLA is an integrated research facility located at UCLA and UC Santa Barbara. Its mission is to foster interdisciplinary collaborations in nanoscience and nanotechnology; to train a new generation of scientists, educators and technology leaders; to generate partnerships with industry; and to contribute to the economic development and the social well-being of California, the United States and the world. The CNSI was established in 2000 with $100 million from the state of California. An additional $850 million of support has come from federal research grants and industry funding. CNSI members are drawn from UCLA's College of Letters and Science, the David Geffen School of Medicine, the School of Dentistry, the School of Public Health and the Henry Samueli School of Engineering and Applied Science. They are engaged in measuring, modifying and manipulating atoms and molecules -- the building blocks of our world. Their work is carried out in an integrated laboratory environment. This dynamic research setting has enhanced understanding of phenomena at the nanoscale and promises to produce important discoveries in health, energy, the environment and information technology.

For more news, visit the UCLA Newsroom and follow us on Twitter.

University of California - Los Angeles

Related Engineering Articles from Brightsurf:

Re-engineering antibodies for COVID-19
Catholic University of America researcher uses 'in silico' analysis to fast-track passive immunity

Next frontier in bacterial engineering
A new technique overcomes a serious hurdle in the field of bacterial design and engineering.

COVID-19 and the role of tissue engineering
Tissue engineering has a unique set of tools and technologies for developing preventive strategies, diagnostics, and treatments that can play an important role during the ongoing COVID-19 pandemic.

Engineering the meniscus
Damage to the meniscus is common, but there remains an unmet need for improved restorative therapies that can overcome poor healing in the avascular regions.

Artificially engineering the intestine
Short bowel syndrome is a debilitating condition with few treatment options, and these treatments have limited efficacy.

Reverse engineering the fireworks of life
An interdisciplinary team of Princeton researchers has successfully reverse engineered the components and sequence of events that lead to microtubule branching.

New method for engineering metabolic pathways
Two approaches provide a faster way to create enzymes and analyze their reactions, leading to the design of more complex molecules.

Engineering for high-speed devices
A research team from the University of Delaware has developed cutting-edge technology for photonics devices that could enable faster communications between phones and computers.

Breakthrough in blood vessel engineering
Growing functional blood vessel networks is no easy task. Previously, other groups have made networks that span millimeters in size.

Next-gen batteries possible with new engineering approach
Dramatically longer-lasting, faster-charging and safer lithium metal batteries may be possible, according to Penn State research, recently published in Nature Energy.

Read More: Engineering News and Engineering Current Events
Brightsurf.com is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon.com.