A Surgical Semiconductor Laser With More Precision And Power

November 01, 1996

By making some simple modifications to semiconductor lasers, a pair of University of Rochester researchers has devised a way to make them perform with the power and precision that laser surgeons routinely demand. These small, relatively inexpensive lasers might replace more powerful and costly gas lasers in treating a variety of medical conditions: removing warts, moles, unwanted hair, and tumors, for instance, performing gum surgery, or treating glaucoma.

The work, done by graduate student John Marciante and Professor of OpticsGovind Agrawal, was presented last week at the annual meeting of the Optical Society of America in Rochester.

Most laser surgery today is done using more powerful and expensive gas lasers, since their semiconductor counterparts usually lack the power necessary for most surgery. The Rochester work cleans up the beam produced by a semiconductor laser, creating a sharply focused beam with more power and precision than the beams produced by most such lasers.

"This sounds like a very useful technology for surgery," says Raymond Lanzafame, director of Rochester General Hospital's Laser Center and a practitioner of laser surgery. "The boost in power provided by this technology could make a single semiconductor laser an option for many procedures where other types of lasers are currently used. If you've got a high-quality beam and a high power output, this offers a convenient alternative for use in the operating room."

The useful power output of semiconductor lasers is limited by the tendency of their beams to fragment into a number of parallel but weaker beams. This doesn't pose a problem for applications that don't require much power, such as laser printers or supermarket scanners, but it limits their use in surgery, where higher power and precision are critical. The new laser produces a unified beam no wider than a grain of sand, with the power efficiently packaged in the center. Rochester researchers believe the new design makes possible semiconductor lasers with 6 to 12 watts of power, two to four times as powerful as current devices. Currently the only way for semiconductor lasers to produce such power is for several to be used in tandem, but this results in poor beam quality.

"Traditionally, with higher power you lose the ability to focus a semiconductor laser on its target," Marciante says. "Rather than a single strong beam, you get three to five weaker beams, greatly diminishing the laser's power and performance."

To compensate for this breakdown of semiconductor laser beams -- known as "filamentation" -- Agrawal and Marciante propose inserting two extra layers of slightly modified semiconducting material on either side of the active layer of gallium arsenide, where the beam is formed.

"It's long been known that in filamentation, you get a 'positive' bending in the beams of high-powered semiconductor lasers, but nobody has been able to successfully counteract that with a 'negative' bending before," Marciante says. "The layers we're inserting induce negative bending, resulting in a net bend of zero for the laser beam and keeping it sharply focused."

While a prototype has yet to be built, Agrawal says that the new laser performed well in computer simulations. He adds that since the inserted layers are made of the same semiconducting materials used in the other layers of the laser -- with a small amount of aluminum added to give them slightly different properties -- the new laser shouldn't be significantly costlier or more difficult to produce than current semiconductor lasers.

Lanzafame, who was not involved in this research, says that semiconductor lasers offer several advantages over the gas lasers more widely used in surgery. They're more durable and more user-friendly, he says, since they have no gas tanks to replace or mirrors to care for. Semiconductor lasers are also more efficient than gas lasers: A gas laser can take 5,000 watts of power to run a one-watt laser, but a semiconductor laser requires only five watts to produce the same power. Since they can be mass-produced, semiconductor lasers usually cost only a few thousand dollars, compared to tens of thousands of dollars for a comparable gas laser.

Semiconductor lasers also have an advantage over gas lasers in portability: gas lasers are often immovable refrigerator-sized units. By contrast, a semiconductor laser is the size of a coarse grain of salt. Even when a power source is added, a high-power semiconductor laser apparatus is still no larger than a fist.

The technology may also be applied in the area of information storage; for instance, the new laser's more precise focus might permit the storage of more data on CD-ROMs. Semiconductor lasers are also used in telecommunications and in communications between satellites.

The work, funded by the University and the U.S. Air Force's Phillips Laboratory, which employs Marciante, was published in the July 29 issue of Applied Physics Letters. Agrawal and Marciante are now considering corporate partners to help build the new laser.
-end-


University of Rochester

Related Laser Articles from Brightsurf:

Laser technology: New trick for infrared laser pulses
For a long time, scientists have been looking for simple methods to produce infrared laser pulses.

Sensors get a laser shape up
Laser writing breathes life into high-performance sensing platforms.

Laser-powered nanomotors chart their own course
The University of Tokyo introduced a system of gold nanorods that acts like a tiny light-driven motor, with its direction of motion is determined by the orientation of the motors.

What laser color do you like?
Researchers at the National Institute of Standards and Technology (NIST) and the University of Maryland have developed a microchip technology that can convert invisible near-infrared laser light into any one of a panoply of visible laser colors, including red, orange, yellow and green.

Laser technology: The Turbulence and the Comb
While the light of an ordinary laser only has one single, well-defined wavelength, a so-called ''frequency comb'' consists of different light frequencies, which are precisely arranged at regular distances, much like the teeth of a comb.

A laser for penetrating waves
The 'Landau-level laser' is an exciting concept for an unusual radiation source.

Laser light detects tumors
A team of researchers from Jena presents a groundbreaking new method for the rapid, gentle and reliable detection of tumors with laser light.

The first laser radio transmitter
For the first time, researchers at Harvard School of Engineering have used a laser as a radio transmitter and receiver, paving the way for towards ultra-high-speed Wi-Fi and new types of hybrid electronic-photonic devices.

The random anti-laser
Scientists at TU Wien have found a way to build the 'opposite' of a laser -- a device that absorbs a specific light wave perfectly.

Laser 'drill' sets a new world record in laser-driven electron acceleration
Combining a first laser pulse to heat up and 'drill' through a plasma, and another to accelerate electrons to incredibly high energies in just tens of centimeters, scientists have nearly doubled the previous record for laser-driven particle acceleration at Berkeley Lab's BELLA Center.

Read More: Laser News and Laser Current Events
Brightsurf.com is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon.com.