ONR presents Bowen Award for composite materials test method

November 28, 2007

Arlington, VA--On November 27, the U.S. Office of Naval Research (ONR) honored two engineers who patented a nondestructive method for detecting flaws and anomalies in composite materials. Rear Admiral William E. Landay, Chief of Naval Research, presented the 2006 Vice Admiral Harold G. Bowen Award to Dr. Colin P. Ratcliffe and Dr. Roger M. Crane for their "Nondestructive Method for Detecting Structural Anomalies in Composites," also known as Structural Irregularity and Damage Evaluation Routine or SIDER (U.S. Patent 6,799,126).

Ratcliffe is a professor of Mechanical Engineering at the U.S. Naval Academy and Crane is a senior composites materials engineer in the Structures and Composites Division at the Naval Surface Warfare Center, Carderock Division.

The Bowen Award is named for Vice Admiral Harold Gardiner Bowen, the first Chief of Naval Research, and it recognizes inventions that have been patented by current or former civilian or military Navy personnel, and that have been of great benefit to the Navy. This benefit may be related to the extent of the invention's use, the cost savings it produces, or its contribution to increased military capabilities or quality of life.

Crane and Ratcliffe developed SIDER, a method for testing composite materials to detect flaws, damage, and other structural anomalies. The method is rapid, accurate, and easy to perform and interpret. Additionally, the method does not damage or destroy the material being tested, and it can be used anywhere, eliminating the need to cut samples from the material and send them to a laboratory.

The method involves tapping a composite structure with a specially designed "hammer" and recording data from the resulting mechanical vibrations. Changes in the vibrational properties may indicate flaws or damage in the material. Transducers measure the force of the taps, and accelerometers measure the interactions between the composite material and the vibrations caused by the hammer's tapping. Vibrational readings can be mapped with great precision onto an image of the structure, allowing an engineer to locate anomalies quickly.

Crane and Ratcliffe have used SIDER to check composite materials in the vertical stabilizers of the F-18 Super Hornet aircraft, the twisted rudder on the DDG guided missile destroyer, and a road bridge on Route 896 in Delaware. Crane noted that the entire bridge test was completed in about six hours, about the same amount of time that it takes to complete a ship hull inspection. A similar inspection could take up to two days using conventional ultrasound methods.

Another advantage over ultrasound is that the vibrational readings can be mapped with great precision onto an image of the structure. When an anomaly appears, you can point to an exact location on the ship's hull or other structure and say, "Here's where the flaw is." Adm. Landay noted during the award presentation that detecting damage early on, before a structure fails, has the potential to save lives.
-end-
The Office of Naval Research (ONR) manages science and technology research for the Navy and Marine Corps. ONR sponsors basic and applied research in oceanography, advanced materials, sensors, robotics, biomedical science and technology, electronics, surveillance, mathematics, manufacturing technology, information science, advanced combat systems, and technologies for ships, submarines, aircraft, ground vehicles--and more.

For information about ONR´s programs, go to http://www.onr.navy.mil.

Office of Naval Research

Related Composite Materials Articles from Brightsurf:

New composite material revs up pursuit of advanced electric vehicles
Scientists at Oak Ridge National Laboratory used new techniques to create a composite that increases the electrical current capacity of copper wires, providing a new material that can be scaled for use in ultra-efficient, power-dense electric vehicle traction motors.

Analyzing pros and cons of two composite manufacturing methods
Airplane wings and wind turbine blades are typically created using bulk polymerization in composite manufacturing facilities.

Visualization of functional components to characterize optimal composite electrodes
Researchers have developed a visualization method that will determine the distribution of components in battery electrodes using atomic force microscopy.

Study suggests polymer composite could serve as lighter, non-toxic radiation shielding
A new study suggests that a polymer compound embedded with bismuth trioxide particles holds tremendous potential for replacing conventional radiation shielding materials, such as lead.

Scientists develop stable luminescent composite material based on perovskite nanocrystals
An international team of scientists that includes researchers from ITMO University has developed a new composite material based on perovskite nanocrystals for the purpose of creating miniature light sources with improved output capacity.

Composite metal foams take the heat, move closer to widespread applications
Engineering researchers have demonstrated that composite metal foams (CMFs) can pass so-called 'simulated pool fire testing' with flying colors, moving the material closer to use in applications such as packaging and transportation of hazardous materials.

Using holograms helps in studying the quality of composite materials
Composite materials have a complicated structure and specified mechanical or physical properties.

Scientists develop a composite membrane for long-life zinc-based flow batteries
Researchers led by Profs. LI Xianfeng from the Dalian Institute of Chemical Physics (DICP) of the Chinese Academy of Sciences recently developed a composite membraneĀ for long-life zinc-based flow batteries.

An early warning system for damage in composite materials
A team at the National Institute of Standards and Technology (NIST) has developed a tool to monitor changes in widely used composite materials known as fiber reinforced polymers (FRPs), which can be found in everything from aerospace and infrastructure to wind turbines.

Novel composite antimicrobial film could take a bite out of foodborne illnesses
A novel composite film -- created by the bonding of an antimicrobial layer to conventional, clear polyethylene plastic typically used to vacuum-package foods such as meat and fish -- could help to decrease foodborne illness outbreaks, according to researchers in Penn State's College of Agricultural Sciences.

Read More: Composite Materials News and Composite Materials Current Events
Brightsurf.com is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon.com.