CWRU awarded grant to build battery for smart grid, renewables

November 30, 2012

CLEVELAND -- A Department of Energy agency that funds high-risk, high-payoff research, has awarded engineers at Case Western Reserve University $567,805 to develop a "rustbelt" battery with unprecedented flexibility and utility.

For more than year, the Cleveland-based researchers have been investigating ways to build a flow battery primarily using water and iron, hence the name. A flow battery is essentially an unwrapped battery that can be scaled up to hold and supply electricity to a home or an entire community.

In addition to using cheap, plentiful and environmentally friendly materials, the battery is designed to improve the efficiency of the power grid and accelerate the addition of solar and wind power supplies.

The project was one of 66 funded by DOE's Advanced Research Projects Agency - Energy in the round of awards announced this week, federal officials said. The battery would enhance the nation's economic and energy security and help ensure that the U.S. maintains a technological lead in developing and deploying advanced energy technologies - two of ARPA-E's goals.

The key is a new battery architecture that enables greater energy storage capacity while permitting greater power density.

"You can use the analogy of a car engine," said Robert Savinell, professor of chemical engineering and the project leader. "If you need more horsepower, you need a bigger engine, but the range is limited by the gas tank. To add more range, you add another gas tank."

The researchers plan to add another tank and some new technology to take advantage of the added storage space in their iron flow battery.

The design would enable them to increase the power density, which in turn drives down the cost of operation. At the same time, the new design eliminates the problem of decreased battery discharge time. Think again of the car: an engine delivering 400 horsepower will go through 4 gallons of fuel faster than the same engine delivering 200 horsepower.

By extending the discharge time as needed, the battery would be more useful for a broader range of applications, including storing energy from wind turbines and solar panels and supplying energy when wind wanes and the sun sets. This version of the rustbelt battery could be integrated into a smart grid--charging up when use is low, then adding electricity when demand is high--for industrial and home energy supplies and more.

Due to its flexibility, this new design could be a useful alternative to current storage technologies, such as pumped hydro and compressed air systems, which require large water supplies and land with mixed elevations, or access to airtight caverns.

When demand is low, pumped hydro stations use excess electricity to pump water from a river or reservoir to a reservoir at a higher elevation. When demand rises, the water is released downhill through turbines that produce electricity. Compressed air stations pump air into caverns when demand is low then release the compressed air through gas turbines to produce electricity at high efficiency as demand increases.

The batteries, which can be placed almost anywhere, could also replace "peak power plants" which suppliers turn on, burning fossil fuels or biomaterial to produce power when peak demands exceed the available energy on the grid. The batteries could thereby reduce emissions.

In standard batteries, power and energy densities are limited by wrapping all the materials used to convert chemical energy to electrical energy inside a single cell. The electrodes, which are part of the fuel, are consumed over time, leading to performance loss.

In flow batteries, chemical reactants used to produce electrical energy are stored in two tanks and the electrodes, which are not used as fuel, are housed in a separate chamber. Reactants are pumped through the cell stack and electrons are delivered in one direction to charge the battery and the other direction to discharge the system.

This new battery would exchange the conventional solid electrode in the negative half of the battery cell with a slurry that can be used to help convert chemical energy to electrical and vice-versa. As much slurry as needed can be pumped through the negative chamber and stored in a separate tank. The volume stored determines energy storage capacity, independent of the power density, or, back to the car, how hard you're driving.

"Instead of being limited by the constraints of a traditional electrode and chamber to providing a kilowatt for an hour, the slurry can be pumped in from another tank and enable you to provide a kilowatt for an hour, or two or 10 or 10s of hours," Savinell said

Savinell is working with Jesse Wainright, a fellow chemical engineering professor at Case School of Engineering, and Mirko F. Antloga, director of the university's Electrochemical Engineering and Energy Laboratory.

Their goal is to devise a slurry that enables the battery to discharge at least 90 percent of the energy that it takes to charge and provide an energy storage efficiency of better than 77 percent.

The researchers say the need is growing rapidly and point to studies that forecast the market for grid-level storage will exceed $228 billion over the next decade.

The most common flow batteries are based on vanadium, a metal mined primarily in Russia, China and South Africa. The form used in batteries has recently cost about $5 to $15 per pound. Iron is plentiful in the U.S. A form useful for a flow battery has recently been selling for less than 30 cents per pound.

Vanadium batteries use highly-corrosive sulfuric acid for the electrolyte. Because flow battery tanks can be the size of a freight train car or several of them, the researchers plan to use a benign electrolyte with a pH of about 4, for the safety of workers operating or maintaining them.
-end-


Case Western Reserve University

Related Engineering Articles from Brightsurf:

Re-engineering antibodies for COVID-19
Catholic University of America researcher uses 'in silico' analysis to fast-track passive immunity

Next frontier in bacterial engineering
A new technique overcomes a serious hurdle in the field of bacterial design and engineering.

COVID-19 and the role of tissue engineering
Tissue engineering has a unique set of tools and technologies for developing preventive strategies, diagnostics, and treatments that can play an important role during the ongoing COVID-19 pandemic.

Engineering the meniscus
Damage to the meniscus is common, but there remains an unmet need for improved restorative therapies that can overcome poor healing in the avascular regions.

Artificially engineering the intestine
Short bowel syndrome is a debilitating condition with few treatment options, and these treatments have limited efficacy.

Reverse engineering the fireworks of life
An interdisciplinary team of Princeton researchers has successfully reverse engineered the components and sequence of events that lead to microtubule branching.

New method for engineering metabolic pathways
Two approaches provide a faster way to create enzymes and analyze their reactions, leading to the design of more complex molecules.

Engineering for high-speed devices
A research team from the University of Delaware has developed cutting-edge technology for photonics devices that could enable faster communications between phones and computers.

Breakthrough in blood vessel engineering
Growing functional blood vessel networks is no easy task. Previously, other groups have made networks that span millimeters in size.

Next-gen batteries possible with new engineering approach
Dramatically longer-lasting, faster-charging and safer lithium metal batteries may be possible, according to Penn State research, recently published in Nature Energy.

Read More: Engineering News and Engineering Current Events
Brightsurf.com is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon.com.