Syracuse University researchers contribute new ideas to enhance efficiency of wind turbines

December 20, 2010

One issue confronting the efficiency of wind as a promising renewable energy source is the wind itself--specifically, its changeability. While the aerodynamic performance of a wind turbine is best under steady wind flow, the efficiency of the blades degrades when exposed to conditions such as wind gusts, turbulent flow, upstream turbine wakes and wind shear.

Now, a new type of air-flow technology may soon increase the efficiency of large wind turbines under many different wind conditions.

Researchers from Syracuse University's L.C. Smith College of Engineering and Computer Science (LCS) are testing new intelligent-systems-based active flow control methods with support from the U.S. Department of Energy through the University of Minnesota Wind Energy Consortium. The approach estimates the flow conditions over the blade surfaces from surface measurements, and then uses this information in an intelligent controller to implement real-time actuation on the blades to control the airflow and increase the overall efficiency of the wind turbine system. The work may also reduce excessive noise and vibration due to flow separation.

Initial simulation results completed by LCS researchers Guannan Wang, Basman El Hadidi, Jakub Walczak, Mark Glauser and Hiroshi Higuchi show that flow control applied on the outboard side of the blade beyond the half radius could significantly enlarge the overall operational range of the wind turbine with the same rated power output, or considerably increase the rated output power for the same level of operational range. The results suggest that either the overall operational range of the wind turbine could be effectively enlarged by 80 percent with the same rated power output, or the rated output power could be increased by 20 percent while maintaining the same level of operational range when the control is on. The optimal location for the actuator is found to be on the outboard of the blade beyond half of the radius.

The team is also investigating a characteristic airfoil in a new anechoic wind tunnel facility at SU to determine the airfoil lift and drag characteristics with appropriate flow control while exposed to large-scale flow unsteadiness. In addition, the effects of flow control on the noise spectrum of the wind turbine will be also assessed and measured in the anechoic chamber.

"It is exciting for us to be involved in the world-class wind energy consortium led by the University of Minnesota," says Glauser, professor of mechanical and aerospace engineering. "This is a wonderful opportunity to transition our expertise in intelligent systems for flow control, developed largely through support from the aerospace sector, to this important and growing area of the renewable energy sector.''

Scientists at the University of Minnesota are looking at another inefficiency with wind energy--the drag, which is the resistance felt by the turbine blades as they beat the air. The team at the University of Minnesota's Saint Anthony Falls Lab (SAFL) looked at the effect of placing tiny grooves on turbine blades on drag reduction. The grooves are in the form of triangular riblets scored into a coating on the blade surface. They are so shallow (between 40 and 225 microns) that they can't be seen by the human eye--leaving the blades looking perfectly smooth. Through wind-tunnel tests of 2.5-megawatt turbine airfoil surfaces (becoming one of the popular industry standards) and computer simulations, they have looked at the grooves' efficacy for various groove geometries and angles of attack (how the blades are positioned relative to the air stream).

University of Minnesota researchers Roger Arndt, Leonardo P. Chamorro and Fotis Sotiropoulos, believe that riblets will increase wind turbine efficiency by about 3 percent.

Both of these new ideas for enhancing the efficiency of wind turbines were recently presented at the American Physical Society Division of Fluid Dynamics meeting in Long Beach, Calif. On Nov. 21, the SU research team presented "Benefits of Active Flow Control for Wind Turbine Blades," and researchers at the University of Minnesota presented "On the skin friction drag reduction in large wind turbines using sharp V-grooved riblets."

Syracuse University

Related Engineering Articles from Brightsurf:

Re-engineering antibodies for COVID-19
Catholic University of America researcher uses 'in silico' analysis to fast-track passive immunity

Next frontier in bacterial engineering
A new technique overcomes a serious hurdle in the field of bacterial design and engineering.

COVID-19 and the role of tissue engineering
Tissue engineering has a unique set of tools and technologies for developing preventive strategies, diagnostics, and treatments that can play an important role during the ongoing COVID-19 pandemic.

Engineering the meniscus
Damage to the meniscus is common, but there remains an unmet need for improved restorative therapies that can overcome poor healing in the avascular regions.

Artificially engineering the intestine
Short bowel syndrome is a debilitating condition with few treatment options, and these treatments have limited efficacy.

Reverse engineering the fireworks of life
An interdisciplinary team of Princeton researchers has successfully reverse engineered the components and sequence of events that lead to microtubule branching.

New method for engineering metabolic pathways
Two approaches provide a faster way to create enzymes and analyze their reactions, leading to the design of more complex molecules.

Engineering for high-speed devices
A research team from the University of Delaware has developed cutting-edge technology for photonics devices that could enable faster communications between phones and computers.

Breakthrough in blood vessel engineering
Growing functional blood vessel networks is no easy task. Previously, other groups have made networks that span millimeters in size.

Next-gen batteries possible with new engineering approach
Dramatically longer-lasting, faster-charging and safer lithium metal batteries may be possible, according to Penn State research, recently published in Nature Energy.

Read More: Engineering News and Engineering Current Events is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to